Biomedical subjects

Yih-Min Sun

Publications and source records attributed to Yih-Min Sun.

3 recordsLinked to original sources

PubMed2005

Phosphorylated and hypoacetylated mutant p53 enhances cisplatin-induced apoptosis through caspase-9 pathway in the absence of transcriptional activation or translation.

It is not completely understood how certain epithelial cells harboring mutant p53 have better response to chemotherapy. We investigate the mechanism of cisplatin-induced apoptosis in two resistant cell lines (parental TCCSUP and R273L mutant p53 transfectant) and two sensitive cell lines (V143A and N247I mutant p53 transfectants). Activation of caspase 9 was demonstrated by Western blotting, and specific inhibitor for caspase 9 could inhibit apoptosis. Inhibitors for caspases 1, 2, 6, and 8 had no effect on apoptosis. Transcriptional repression of Bcl-2 occurred during apoptosis and could be reversed by the treatment of histone deacetylase inhibitor trichostatin A (TSA). The expression of Noxa, p53 inducible ribonucleotide reductase subunit 2 (p53R2), and p53 inducible death domain (PIDD) gene were not elevated with treatment of cisplatin (CDDP). Surface trafficking of Fas or Fas-L was not observed. Ser15 of wild-type p53 and mutant p53 was phosphorylated in response to cisplatin. Acetylation of wild-type p53 increased, while acetylation of mutant p53 decreased during cisplatin treatment. Both transcriptional inhibitor actinomycin D and translational inhibitor cycloheximide did not inhibit apoptosis. These results indicated that phosphorylated and hypoacetylated mutant p53 could enhance cisplatin-induced apoptosis through activation of caspase 9 independent of transcriptional activation and translation.

Acetylation↗

PubMed2003

The feasibility study of the octane-enhancing process: isobutylene dimerization using C4 mixture.

The dimerization of isobutylene to diisobutylene in C4 mixture was evaluated using various catalysts such as nickel salts system, zeolite system and acidic ion exchange resin. There were shown that the strong acidic type ion exchange resin (Amberlyst 15) under 6 kg/cm2 and 60 degrees C gave rise to 90% conversion and more than 60% selectivity to diisobutylene with acceptable amounts of oligomer as a best catalyst. Therefore, Amberlyst 15 was employed to investigate the optimum reaction condition. In the batch reaction, since the catalyst activity was increased with the increasing reaction temperature, the reaction time should be shortened appropriately to prevent a high yield of oligomer. The reaction rate was increased by the increased amount of catalyst without much change in the product composition. The formation of oligomer was inhibited when a small amount of organic solvents (methyl tert-butyl ether) are attended. In the fixed-bed study, the results indicate that the increase in reaction temperature was accompanied by the increase in reaction rate, however, the selectivity to the dimer was affected. Higher WHSV will enhance the selectivity but reduce the conversion. Conclusively, the appropriate reaction condition was 45 degrees C with WHSV of 10.

Air Pollution↗

PubMed2003

Evaluating the efficacy of a thermal exposure chamber designed for assessing workers' thermal hazard.

This study was conducted on a thermal exposure chamber designed for assessing workers' thermal hazard. In order to assess the efficacy of the studied chamber, three environmental conditions were selected to simulate high, middle and low thermal impact situations, with air temperatures (Ta) of 43.12, 36.23 and 25.77 masculine C, globe temperatures (Tg) of 44.41, 41.07 and 29.24 masculine C, relative humidity (RH) of 77, 59 and 39%, and air flow velocities (Va) of 1.70, 0.91 and 0.25 m/s, respectively. For the three specified thermal impact conditions, results show that the coefficients of variation (CVs) for Ta, Tg, RH and Va measured in the chamber studied were consistently less than 10%, except for Va under the low thermal impact condition (=50%). For each specified thermal impact condition, we generated 1,000 environmental combinations by using the Monte Carlo simulation approach according to the variations obtained from the four environmental factors. We directly adopted the ISO 7933 approach to estimate the allowable exposure time (AET) for each simulated environmental condition. This study yielded a range in the 95% confidence interval (95% CI) of the estimated AETs for the three specified thermal impact conditions which were consistently less than 5 min. We further conducted the sensitivity analysis to examine the effect of the four environmental factors on estimating AETs. We found Va was the least important factor in estimating AETs for any specified thermal impact condition. In conclusion, although Va was found with great variation for the chamber specified in the low thermal impact condition, the exposure chamber studied can still be regarded as a feasible one for assessing workers' thermal hazard.

Environmental Monitoring↗