Biomedical subjects

Yurko Duda

Publications and source records attributed to Yurko Duda.

5 recordsLinked to original sources

PubMed2006

Negative linear compressibility in confined dilatating systems.

The role of a matrix response to a fluid insertion is analyzed in terms of a perturbation theory and Monte Carlo simulations applied to a hard sphere fluid in a slit of fluctuating density-dependent width. It is demonstrated that a coupling of the fluid-slit repulsion, spatial confinement, and the matrix dilatation acts as an effective fluid-fluid attraction, inducing a pseudocritical state with divergent linear compressibility and noncritical density fluctuations. An appropriate combination of the dilatation rate, fluid density, and the slit size leads to the fluid states with negative linear compressibility. It is shown that the switching from positive to negative compressibility is accompanied by an abrupt change in the packing mechanism.

Journal Article↗

PubMed2005

Corrosion inhibitors: design, performance, and computer simulations.

The development of a methodology to predict the performance of a corrosion inhibitor (CI) using specific types of modeled and experimental surfaces and their subsequent estimation is presented. For previously reported imidazoline CIs, the theoretical partition coefficients and molecular volumes were calculated, providing a guide for molecular engineering of new imidazolines. The new CIs, N-[2-(2-alkyl-4,5-dihydroimidazol-1-yl)ethyl]alkylamides and N-[2-(2-alkyloylaminoethylamino)ethyl]alkylamides, were designed, prepared, and their theoretical partition coefficients and molecular volumes calculated. These indexes were correlated between tested and prototype CIs to select the best ones for the corrosion inhibition tests. The inhibition efficiencies were measured through potentiodynamic polarization curves (PPC), linear polarization resistance (LPR), and weight loss measurements (WLM) for SAE-1010 and SAE-1018 steels. The leading molecules were 1-(2-decylaminoethyl)-2-decylimidazoline and 1-(2-dodecylaminoethyl)-2-dodecylimidazoline with WLM efficiencies (steel 1010), of 62.8 and 78.9%, respectively. The efficiencies for the PPC/LPR tests (steel 1018) were 97 and 94%. To understand the mechanism of action of CIs, a simple model is suggested for the growth of self-assembled monolayers of CIs on a crystalline substrate. This model takes into account the amphiphilic nature of the inhibitor molecule on the adsorption process. Despite the simplicity of the model, the Monte Carlo simulations reproduce qualitatively many of the experimentally observed features involved in the formation of monolayers and provide a tentative explanation for the mechanism of corrosion inhibition.

Journal Article↗

PubMed2005

Modeling of drying in films of colloidal particles.

The process of film formation on a solid substrate from polymer colloid dispersion during solvent evaporation has been investigated by means of the Monte Carlo simulation method. Colloid particles are modeled as hard spheres. Time evolution of the colloid density distribution and coverage of the solid substrate are studied. Both density and structure of colloid film is shown to depend strongly on the evaporation rate. At a low evaporation rate, the coexistence of hexagonal and tetragonal domains of dried colloid monolayer has been observed. The results of monolayer structure are in good agreement with the confocal scanning laser microscopy observations of Dullens et al. (2004).

Comment↗

PubMed2005

Modeling of composite latex particle morphology by off-lattice Monte Carlo simulation.

Composite latex particles have shown a great range of applications such as paint resins, varnishes, water borne adhesives, impact modifiers, etc. The high-performance properties of this kind of materials may be explained in terms of a synergistical combination of two different polymers (usually a rubber and a thermoplastic). A great variety of composite latex particles with very different morphologies may be obtained by two-step emulsion polymerization processes. The formation of specific particle morphology depends on the chemical and physical nature of the monomers used during the synthesis, the process temperature, the reaction initiator, the surfactants, etc. Only a few models have been proposed to explain the appearance of the composite particle morphologies. These models have been based on the change of the interfacial energies during the synthesis. In this work, we present a new three-component model: Polymer blend (flexible and rigid chain particles) is dispersed in water by forming spherical cavities. Monte Carlo simulations of the model in two dimensions are used to determine the density distribution of chains and water molecules inside the suspended particle. This approach allows us to study the dependence of the morphology of the composite latex particles on the relative hydrophilicity and flexibility of the chain molecules as well as on their density and composition. It has been shown that our simple model is capable of reproducing the main features of the various morphologies observed in synthesis experiments.

Journal Article↗

PubMed2004

Liquid-vapor interface of square-well fluids of variable interaction range.

Properties of the liquid-vapor interface of square-well fluids with ranges of interaction lambda=1.5, 2.0, and 3.0 are obtained by Monte Carlo simulations and from square-gradient theories that combine the Carnahan-Starling equation of state for hard spheres with the second and third virial coefficients. The predicted surface tensions show good agreement with the simulation results for lambda=2 and for lambda=3 in a temperature range reasonably close to the critical point, 0.8</=T/T(c)</=0.95. As expected, the surface tension increases with the range of interaction and decreases monotonically with temperature. A comparison between theory and simulation results is also given for the width of the interface and for the coexistence curves for the different interaction ranges.

Journal Article↗