PubMed Health⌕ Search
Home/Archive/PubMed

PubMed · 10367459

Implementation and application of real-time motion analysis based on passive markers.

G Baroni·G Ferrigno·A Pedotti
View original source ↗Export metadata ↓

Abstract

A method for real-time motion analysis based on passive markers is presented. An opto-electronic automatic motion analyser was used as hardware platform and the real-time operation was based on the interfacing between two levels of the system architecture. True real-time acquisition, processing and representation of two-dimensional and three-dimensional kinematics data were implemented through a newly conceived data acquisition procedure and high speed optimisation of the kinematics data processing. The method allows one to operate the motion analysis system in real-time; even when the data elaboration unit is required to perform other processing functions, the only consequence is a decrease in system sampling rate. The maximum number of processed and plotted markers in three dimensions at the highest system sampling rate (100 Hz) turned out to be suitable for the implementation of analytical and visual kinematics biofeedback. An example of the achievable level of complexity in terms of marker disposition model and graphic representation is reported by describing a demonstration of the real-time representation of human face movements. A clinical application of the method for patient position definition and control at radiotherapy units is presented.

Explore related subjects

Biomechanical PhenomenaFaceHumansImage Processing, Computer-AssistedMovementPhotogrammetryRadiotherapyJournal Article

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

G Baroni, G Ferrigno, A Pedotti. 1998. Implementation and application of real-time motion analysis based on passive markers.. https://doi.org/10.1007/bf02518871

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related citations

PubMed2007

The effect of excessive tibial torsion on the capacity of muscles to extend the hip and knee during single-limb stance.

Excessive tibial torsion, a rotational deformity about the long axis of the tibia, is common in patients with cerebral palsy who walk with a crouch gait. Previous research suggests that this deformity may contribute to crouch gait by reducing the capacity of soleus to extend the knee; however, the effects of excess external torsion on the capacity of other muscles to extend the stance limb during walking are unknown. A computer model of the musculoskeletal system was developed to simulate a range of tibial torsion deformities. A dynamic analysis was then performed to determine the effect of these deformities on the capacity of lower limb muscles to extend the hip and knee at body positions corresponding to the single-limb stance phase of a normal gait cycle. Analysis of the model confirmed that excessive external torsion reduces the extension capacity of soleus. In addition, our analysis revealed that several important muscles crossing the hip and knee are also adversely affected by excessive tibial torsion. With a tibial torsion deformity of 30 degrees , the capacities of soleus, posterior gluteus medius, and gluteus maximus to extend both the hip and knee were all reduced by over 10%. Since a tibial torsion deformity reduces the capacity of muscles to extend the hip and knee, it may be a significant contributor to crouch gait, especially when greater than 30 degrees from normal, and thus should be considered by clinicians when making treatment decisions.

Biomechanical Phenomena↗
PubMed2007

Predicting the subject-specific primary stability of cementless implants during pre-operative planning: preliminary validation of subject-specific finite-element models.

Pre-operative planning help the surgeon in taking the proper clinical decision. The ultimate goal of this work is to develop numerical models that allow the surgeon to estimate the primary stability during the pre-operative planning session. The present study was aimed to validate finite-element (FE) models accounting for patient and prosthetic size and position as planned by the surgeon. For this purpose, the FE model of a cadaveric femur was generated starting from the CT scan and the anatomical position of a cementless stem derived by a skilled surgeon using a pre-operative CT-based planning simulation software. In-vitro experimental measurements were used as benchmark problem to validate the bone-implant relative micromotions predicted by the patient-specific FE model. A maximum torque in internal rotation of 11.4 Nm was applied to the proximal part of the hip stem. The error on the maximum predicted micromotion was 12% of the peak micromotion measured experimentally. The average error over the entire range of applied torques was only 7% of peak measurement. Hence, the present study confirms that it is possible to accurately predict the level of primary stability achieved for cementless stems using numerical models that account for patient specificity and surgical variability.

Biomechanical Phenomena↗
PubMed2007

Experimental validation of intact and implanted distal femur finite element models.

Four finite element (FE) models of intact and distal femur of knee replacements were validated relative to measured bone strains. FE models of linear tetrahedrons were used. Femoral replacements with cemented stemless, cemented and noncemented femoral stems of the PFC Sigma Modular Knee System were analyzed. Bone strains were recorded at ten locations on the cortex. The magnitude of the FE bone strains corresponded to the mean measured strains, with an overall agreement of 10%. Linear regression between the FE and mean experimental strains produced slopes between 0.94 and 1.06 and R(2) values between 0.92 and 0.99. RSME values were less than 12%. The FE models were able to adequately replicate the mechanical behavior of distal femur reconstructions.

Biomechanical Phenomena↗