PubMed Health⌕ Search

PubMed · 10853757

Introduction: basic concepts and definitions in mechanics.

Abstract

This introduction aims to expound the basic ideas of mechanics of materials to clinicians. What happens when a bone (mechanically a beam) is submitted to standard loads: Centric axial load, bending, eccentric axial load, torque? How does the bone deform? The basic ideas of mechanical engineering are presented using an eraser under load as an illustrative object, and trying to maintain the mathematical formulae as far as possible.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

J Cordey. 2000. Introduction: basic concepts and definitions in mechanics.. https://doi.org/10.1016/s0020-1383(00)80039-x

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related citations

Cell adhesion on poly(propylene fumarate-co-ethylene glycol) hydrogels.

We synthesized poly(propylene fumarate-co-ethylene glycol) block copolymers [P(PF-co-EG)] that were crosslinked to form hydrogels and investigated the effect of copolymer composition on cell adhesion to the hydrogels. These copolymers were water soluble when the molar ratio of ethylene glycol repeating unit to propylene fumarate repeating unit was higher than 4.4. The water content of swollen hydrogels increased from 29 to 63% and the water contact angle decreased from 38 to 21 degrees as the molar ratio increased from 0.6 to 4.4. No significant change in either property was observed for ratios higher than 4.4. In a cell adhesion assay under serum-free conditions, the number of adherent platelets and smooth muscle cells decreased from 21 to 2% and from 78 to 20% of the initial seeding density, respectively, as the molar ratio increased from 0.6 to 7.8. Adherent smooth muscle cells did not spread on the hydrogels of the compositions tested. Adherent platelets did not show any filopodia. These results suggest that the hydrophilicity of P(PF-co-EG) hydrogels is one of the factors affecting cell adhesion, and that copolymer modification may be required for enhancing cell adhesion for an application involving the copolymers as in situ crosslinkable cell carriers.

Biocompatible Materials↗

Biocompatibility of dense hydroxyapatite prepared using an SPS process.

In the present study, the preparation of dense hydroxyapatite (HAp) materials at relative low temperatures using a spark plasma sintering was carried out. The bioactivity of HAp samples prepared by a spark plasma sintering method was investigated by in vitro tests and compared with HAp obtained by a conventional hot-pressing method. No growth of bone-like HAp crystals on surface of HAp sintered by a conventional hot-pressing method at 1200 degrees C was observed after immersion in a simulated body fluid (SBF) for 2 days. However, many large bone-like HAp crystals were observed on the surface of HAp samples prepared by a spark plasma sintering at 1200 degrees C after 2 days in the SBF immersion test. Especially, the negatively charged surface of the HAp samples prepared by spark plasma sintering was covered with larger HAp crystals compared with the positively charged surface. The electric poling of HAp was measured using a thermally simulated current technique. This rapid growth of bone-like HAp crystals of the HAp samples made by spark plasma sintering was believed to be related with the OH(-) and/or Ca(2(+) ) ion deficiency at the grain boundaries of the HAp matrix grains as well as a small electric poling effect resulting during the spark plasma sintering process.

Biocompatible Materials↗

Characterization of microrough bioactive glass surface: surface reactions and osteoblast responses in vitro.

The current study characterized the in vitro surface reactions of microroughened bioactive glasses and compared osteoblast cell responses between smooth and microrough surfaces. Three different bioactive glass compositions were used and surface microroughening was obtained using a novel chemical etching method. Porous bioactive glass specimens made of sintered microspheres were immersed in simulated body fluid (SBF) or Tris solutions for 1, 6, 24, 48, or 72 h, and the formation of reaction layers was studied by means of a scanning electron microscope/energy dispersive X-ray analysis (SEM/EDXA). Cell culture studies were performed on bioactive glass disks to examine the influence of surface microroughness on the attachment and proliferation of human osteoblast-like cells (MG-63). Cell attachment was evaluated by means of microscopic counting of in situ stained cells. Cell proliferation was analyzed with a nonradioactive cell proliferation assay combined with in situ staining and laser confocal microscopy. The microroughening of the bioactive glass surface increased the rate of the silica gel layer formation during the first hours of the immersion. The formation of calcium phosphate layer was equal between control and microroughened glass surfaces. In cell cultures on bioactive glass, the microrough surface enhanced the attachment of osteoblast-like cells but did not have an effect on the proliferation rate or morphology of the cells as compared with smooth glass surface. In conclusion, microroughening significantly accelerated the early formation of surface reactions on three bioactive glasses and had a positive effect on initial cell attachment.

Biocompatible Materials↗