PubMed Health⌕ Search
Home/Archive/PubMed

PubMed · 11114660

Model for on-line moisture-content control during solid-state fermentation.

F J Nagel·J Tramper·M S Bakker·A Rinzema
View original source ↗Export metadata ↓

Abstract

In this study we describe a model that estimates the extracellular (nonfungal) and overall water contents of wheat grains during solid-state fermentation (SSF) with Aspergillus oryzae, using on-line measurements of oxygen, carbon dioxide, and water vapor in the gas phase. The model uses elemental balances to predict substrate dry matter losses from carbon dioxide measurements, and metabolic water production, water used in starch hydrolysis, and water incorporated in new biomass from oxygen measurements. Water losses caused by evaporation were calculated from water vapor measurements. Model parameters were determined using an experimental membrane-based model system, which mimicked the growth of A. oryzae on the wheat grains and permitted direct measurement of the fungal biomass dry weight and wet weight. The measured water content of the biomass depended heavily on the moisture content of the solid substrate and was significantly lower than the estimated values reported in the literature. The model accurately predicted the measured overall water content of fermenting solid substrate during fermentations performed in a 1.5-L scraped drum reactor and in a 35-L horizontal paddle mixer, and is therefore considered validated. The model can be used to calculate the water addition required to control the extracellular water content in a mixed solid-state bioreactor for cultivation of A. oryzae on wheat.

Explore related subjects

Aspergillus oryzaeBiomassBioreactorsCarbon DioxideFermentationIndustrial MicrobiologyMembranes, ArtificialModels, BiologicalOxygenPredictive Value of TestsReproducibility of ResultsTriticumWaterJournal ArticleResearch Support, Non-U.S. Gov't

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

F J Nagel, J Tramper, M S Bakker, A Rinzema. 2001-01-20. Model for on-line moisture-content control during solid-state fermentation.. https://doi.org/10.1002/1097-0290(20000120)72%3A2%3C231%3A%3Aaid-bit11%3E3.0.co%3B2-s

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related citations

PubMed2026

Bioengineering and physicochemical optimization of ergothioneine production by Aspergillus oryzae.

Ergothioneine (EGT) is a bioactive, rare variant of histidine with many applications in the medical, pharmaceutical, and food fields. Therefore, we aimed to investigate in this study the impact of genomic and physicochemical factors on EGT production by the industrial filamentous fungus Aspergillus oryzae. Firstly, to facilitate efficient EGT production, we analyzed the subcellular localization of the three EGT biosynthetic enzymes present in A. oryzae. During screening for the most potent producer of EGT among bioengineered transformants, the strain EgtACO overexpressing both AoegtA and AoegtC showed promising EGT production in DPY medium. Five days of incubation was the optimum period, and CZYP medium was the optimum medium for EGT production. Co-cultivation with the nisin Z-producing Lactococcus lactis JCM 7638 yielded EGT production equivalent to that of the EgtACO strain alone. Having broad-spectrum antimicrobial activity without suppressing growth of the EgtACO strain suggested that bacteriocin may help reduce the risk of contamination during long-term cultivation. Moreover, supplementing the production medium with L-methionine or zinc sulfate improved EGT production (1468.5 or 1565 mg/L, respectively). Furthermore, repeated inoculation of the producer strain EgtACO and incubation in blue light were the optimum conditions for EGT production (1895 mg/L). Finally, we achieved cost-effective EGT production using A. oryzae strain EgtACO under the optimal culture conditions using agricultural wastes: potato peel and sweet potato peel (293 and 308 mg/L, respectively).

Aspergillus oryzae↗
PubMed2002

Dependence of morphology on agitation intensity in fed-batch cultures of Aspergillus oryzae and its implications for recombinant protein production.

We previously reported that, although agitation conditions strongly affected mycelial morphology, such changes did not lead to different levels of recombinant protein production in chemostat cultures of Aspergillus oryzae (Amanullah et al., 1999). To extend this finding to another set of operating conditions, fed-batch fermentations of A. oryzae were conducted at biomass concentrations up to 34 g dry cell weight/L and three agitation speeds (525, 675, and 825 rpm) to give specific power inputs between 1 and 5 kWm(-3). Gas blending was used to control the dissolved oxygen level at 50% of air saturation except at the lowest speed where it fell below 40% after 60-65 h. The effects of agitation intensity on growth, mycelial morphology, hyphal tip activity, and recombinant protein (amyloglucosidase) production in fed-batch cultures were investigated. In the batch phase of the fermentations, biomass concentration, and AMG secretion increased with increasing agitation intensity. If in a run, dissolved oxygen fell below approximately 40% because of inadequate oxygen transfer associated with enhanced viscosity, AMG production ceased. As with the chemostat cultures, even though mycelial morphology was significantly affected by changes in agitation intensity, enzyme titers (AGU/L) under conditions of substrate limited growth and controlled dissolved oxygen of >50% did not follow these changes. Although the measurement of active tips within mycelial clumps was not considered, a dependency of the specific AMG productivity (AGU/g biomass/h) on the percentage of extending tips was found, suggesting that protein secretion may be a bottle-neck in this strain during fed-batch fermentations.

Aspergillus oryzae↗
PubMed2002

Estimation of hyphal tensile strength in production-scale Aspergillus oryzae fungal fermentations.

Fragmentation of filamentous fungal hyphae depends on two phenomena: hydrodynamic stresses, which lead to hyphal breakage, and hyphal tensile strength, which resists breakage. The goal of this study was to use turbulent hydrodynamic theory to develop a correlation that allows experimental data of morphology and hydrodynamics to be used to estimate relative (pseudo) tensile strength (sigma(pseudo)) of filamentous fungi. Fed-batch fermentations were conducted with a recombinant strain of Aspergillus oryzae in 80 m(3) fermentors, and measurements were made of both morphological (equivalent hyphal length, L) and hydrodynamic variables (specific power input, epsilon; kinematic viscosity, v). We found that v increased over 100-fold during these fermentations and, hence, Kolmogorov microscale (lambda) also changed significantly with time. In the impeller discharge zone, where hyphal fragmentation is thought to actually take place, lambda was calculated to be 700-3500 microm, which is large compared to the size of typical fungal hyphae (100-300 microm). This result implies that eddies in the viscous subrange are responsible for fragmentation. Applying turbulent theory for this subrange, it was possible to calculate sigma(pseudo)from morphological and hydrodynamic measurements. Pseudo tensile strength was not constant but increased to a maximum during the first half and then decreased during the second half of each fermentation, presumably due to differences in physiological state. When a literature correlation for hyphal fragmentation rate (k(frag)) was modified by adding a term to account for viscosity and tensile strength, the result was better qualitative agreement with morphological data. Taken together, these results imply hyphal tensile strength can change significantly over the course of large-scale, fed-batch fungal fermentations and that existing fragmentation and morphology models may be improved if they accounted for variations in hyphal tensile strength with time.

Aspergillus oryzae↗