PubMed Health⌕ Search
Home/Archive/PubMed

PubMed · 11677541

Modified flasking technique for processing a maxillary resection obturator with continuous pressure injection.

H S Cotert·C Cura·A Kesercioglu
View original source ↗Export metadata ↓

Abstract

It is not possible for the wax pattern of most large-volume maxillary resection obturators to be placed into a flask for conventional compression molding processing and positioning of the wax pattern. However, these wax patterns and their channel access design often can be modified and aligned in position for processing with the continuous pressure injection technique. This article describes the use of the continuous pressure injection technique to process the perpendicularly aligned wax pattern of a maxillary resection obturator. It also describes a modified channel design and a simple method to pull back the injection funnel to increase the volume of the flask.

Explore related subjects

Calcium SulfateDental MaterialsHumansInjectionsMaxillaPalatal ObturatorsPolymethyl MethacrylatePressureProsthesis DesignSurface PropertiesWaxesJournal Article

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

H S Cotert, C Cura, A Kesercioglu. 2001. Modified flasking technique for processing a maxillary resection obturator with continuous pressure injection.. https://doi.org/10.1067/mpr.2001.118222

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related citations

PubMed2003

Refined gypsum effective attenuation coefficients for Co-60, 6 MV, 10 MV and 18 MV x-rays.

We report new effective linear attenuation coefficients (mueff) for refined gypsum for Co-60 and 18 MV x-rays. 6 MV and 10 MV mueff agree with published data. For a 100 cm2 field size (FS), tissue defect x = 1.35 cm, target depth d = 1.65 cm beneath the tissue defect x, mueff is 0.123 cm(-1) (Co-60) and 0.0934 cm(-1) (6 MV). For 100 cm2, x = 1.35 cm, and d = 5.65 cm beneath x, mueff is 0.072 cm(-1) (10 MV), and 0.0614 cm(-1) (18 MV). Ford, mueff decreases about 10% from 25 to 400 cm2. For a given FS, mueff decreases with d by 3%-5% for Co-60, and 3% for 6 MV, 10 MV and 18 MV, but depends on (d - x). For d, when x is large (8 cm), depending on energy and FS, mueff is 2%-4% less than when x is small (2 cm). These data were used in a treatment-planning computer to design compensator filters for a step phantom. Compensation was to within 10% in the compensation plane (CP). Above and below CP, computer-calculated ratios of doses with and without filters were 0.75-1.13. Chamber dose ratios with and without filters were 0.75-1.12.

Calcium Sulfate↗
PubMed2003

A new gypsum-based technique to reduce methane and phophorus release from sediments of eutrophied lakes: (gypsum treatment to reduce internal loading).

The release of nutrients from the sediment into the water column, i.e. internal nutrient loading, is an important problem in the restoration of eutrophied lakes. The ebullition of gases, mainly methane, has been identified as the key process in nutrient transportation in the internal loading. We studied whether methane production in lake sediment and the release of nutrients into the water column could be prevented by the addition of gypsum (CaSO4 x 2H2O). Three different gypsum products were examined in a controlled laboratory microcosm with a continuous water flow. The addition of gypsum (especially Fe-gypsum) into the sediment increased the redox potentials and reduced methane production and release of phosphorus from the sediments during an incubation period of 3 months. Gypsum evidently acted as a slow-releasing source of sulphate in sediment, which likely enhanced the activity of sulphate-reducing bacteria and improved the overall mineralisation rate of organic matter. The liberation of H2S and phosphate, which might be an undesired consequence of increased sulphate reduction rates was prevented by the application of Fe-containing gypsum likely as a result of the formation of pyrite and apatite minerals.

Calcium Sulfate↗
PubMed2003

A new method for the computer-aided evaluation of three-dimensional changes in gypsum materials.

OBJECTIVES: The quantitative evaluation of the time- or process-dependent three-dimensional stability of dental materials is a common question in dentistry. An investigation procedure has been developed based on a CAD-surface model of a prepared upper canine, as well as a high-precision physical copy (metal master die). The specific aim of this study was to test this method's reliability. Additionally, the ability of the developed procedure to determine the three-dimensional stability of resin-reinforced gypsum master casts over time was investigated. METHODS: Ten duplicate dies of improved dental stone (esthetic-rock, dentona, Germany) were manufactured, and digitized 1, 3, 7, 28 and 56 days after pouring. A three-coordinate optical measuring device was used for the data acquisition. The three-dimensional accuracy of stone dies was determined by comparing the digitized data of the stone dies made from the metal master die to its CAD-surface model (Surfacer) Version 9.0. Imageware Inc., Ann Arbor Michigan, USA). To assess the procedure, test surfaces were created from the digitized data and compared with a reference. RESULTS: The mean deviation between the digitized point cloud and the test surface was less than 3 microm. During the 56 day examination period no significant three-dimensional changes in dimensional stability were found. SIGNIFICANCE: The procedure for the quantitative three-dimensional evaluation was shown to be suitable. Best-fit registration enabled a reliable alignment of the point cloud to the CAD-surface model. Alteration of three-dimensional accuracy over 6 weeks was insignificant and without clinical relevance.

Calcium Sulfate↗