Impression techniques for removable partial dentures.

W F Turbyfill

PubMed · 12016678

Impression techniques for removable partial dentures.

Abstract

This article concerns a subject that has been very perplexing to dentists attempting to provide superior removable prosthetic services. The techniques in this article have been developed, tried, and proven over 42 years of clinical practice. Adequate impressions for partial denture construction when crowns that have been fitted to the mouth are included as part of the master cast. The dilemma of having already cemented crowns with attachments on them can be a problem. An easy technique has been developed for analog production in these cases.

Explore related subjects

Alginates Crowns Dental Abutments Dental Impression Materials Dental Impression Technique Denture Design Denture Precision Attachment Denture, Partial, Removable Denture, Partial, Temporary Equipment Design Humans Models, Dental Patient Care Planning Journal Article

Keep this discovery

Explore connections, maps & timelines

BibTeX RIS

W F Turbyfill. Impression techniques for removable partial dentures.. https://pubmed.ncbi.nlm.nih.gov/12016678/

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related citations

PubMed2003

Compression of biocompatible liquid-filled HSA-alginate capsules: determination of the membrane mechanical properties.

Compression experiments between two parallel plates are performed on a series of biocompatible HSA-alginate capsules with two different membrane thicknesses. The capsule geometry and size as well as the average membrane thickness are first measured. The compression set-up is fitted with a sensitive force transducer that allows measurement of the compression force as a function of plate separation. The response of the capsule is analyzed by assuming different constitutive models for the membrane, where the shear and surface dilatation effects are accounted. An apparent area dilatation modulus is then computed for different values of the plate separation and required to remain constant as the capsule deformation increases. This allows identification of plausible constitutive laws for the membrane material.

Alginates↗

PubMed2003

Improvement of the biocompatibility of alginate/poly-L-lysine/alginate microcapsules by the use of epimerized alginate as a coating.

Alginate/poly-L-lysine(PLL)/alginate capsules are used widely for the microencapsulation of cells. Alginate consists of guluronic acid and mannuronic acid, the ratio and sequence of which affect the properties of the alginate. Using C5-epimerases, mannuronic acid can be converted to guluronic acid in the alginate polymer. Such an enzyme, AlgE4, was used to convert blocks of mannuronic acid (M-blocks) to blocks of alternating sequence (MG-blocks). The aims of this study were 1) to investigate whether the use of epimerized alginate as a coating could improve the biocompatibility of alginate/PLL/alginate capsules and 2) to study the biocompatibility of simple alginate beads prepared with epimerized alginate. Four different capsules, two of which contained epimerized alginate, were investigated after implantation in C57BL/6 mice for 1 week. The biocompatibility of alginate/PLL/alginate capsules, as measured by retrieval rates of the capsules and DNA contents and glucose oxidation rates of the cellular overgrowth, was improved when an epimerized coating alginate was used. There were, however, no statistically significant differences in the biocompatibility of simple alginate beads made from epimerized alginate when compared with non-epimerized alginate beads. In general, such beads produced without a PLL coating swelled to a higher extent than the conventional alginate/PLL/alginate capsules. In conclusion, the use of an epimerized coating on alginate-PLL-alginate can improve the biocompatibility of such capsules but still cannot completely eliminate the detrimental effects of PLL on the biocompatibility of the capsules.

Alginates↗

PubMed2003

Microcapsules made by enzymatically tailored alginate.

Alginate is widely used for encapsulation of cells. Alginate is a linear block copolymer consisting of mannuronic acid (M) and guluronic acid (G). It has been shown that enzymes known as C-5 epimerases convert M to G in the polymer chain, giving rise to novel alginates with tailored properties. One of these enzymes, AlgE4, converts M blocks into blocks of strictly alternating M and G. In this study we investigated how alginate epimerized by AlgE4 affected capsule properties such as stability and permeability. Inhomogeneous calcium-alginate gel beads were made with original and AlgE4-epimerized alginates of different origin. The epimerized alginates formed initially smaller alginate gels that showed increased resistance to osmotic swelling compared with the original nonmodified alginate samples. The permeability, measured as diffusion of immunoglobulin (Ig) G into Ca/Ba-alginate gel beads, was reduced by epimerization and further reduced by addition of poly-L-lysine (PLL). The osmotic stability of alginate-poly-D-lysine(PDL)-alginate capsules was enhanced by the use of epimerized alginate; indeed, stable capsules with low permeability to tumor necrosis factor (TNF) could be made with low PDL exposures. Finally, alginate with an alternating structure interacted more strongly with the alginate-PLL capsule than did alginate with a high content of M blocks or G blocks or than an alginate consisting mainly of M.

Alginates↗