PubMed Health⌕ Search
Home/Archive/PubMed

PubMed · 14511736

An optimized synthetic substrate for orthodontic bond strength testing.

A Klocke·D Tadic·B Kahl-Nieke·M Epple
View original source ↗Export metadata ↓

Abstract

OBJECTIVE: The purpose of this study was to investigate the suitability of different synthetic calcium phosphate based substrates as a biomimetic enamel surface model for orthodontic bond strength testing. METHODS: Carbonated apatite, amorphous calcium phosphate and commercial hydroxyapatite specimens were prepared as substrates for orthodontic bond strength testing. Carbonated apatite specimens were prepared by pressing, sintering and treatment with NaF. The shear bond strength was measured with a universal testing machine. RESULTS: Hydroxyapatite, amorphous and cold pressed carbonated hydroxyapatite exhibited fractures within the substrate after debonding. Mean bond strength values for carbonated hydroxyapatite were 7.38 (1.75) MPa for specimens pressed at 300 degrees C and 9.55 (2.23) MPa for specimens pressed at 300 degrees C and then sintered at 600 degrees C. An additional NaF treatment after sintering resulted in lower bond strength measurements of on average 6.52 (1.03) MPa. SIGNIFICANCE: Hot pressed and sintered carbonated hydroxyapatite showed acceptable shear bond strength values and may represent a suitable biomimetic model for orthodontic bond strength testing.

Explore related subjects

ApatitesBiomimetic MaterialsCalcium PhosphatesCarbonatesDental BondingDental EnamelDental Stress AnalysisDurapatiteHumansMaterials TestingOrthodontic BracketsPressureSodium FluorideStress, MechanicalSurface PropertiesTemperatureJournal Article

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

A Klocke, D Tadic, B Kahl-Nieke, M Epple. 2003. An optimized synthetic substrate for orthodontic bond strength testing.. https://doi.org/10.1016/s0109-5641(03)00025-3

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related citations

PubMed2007

Plasma-controlled nanocrystallinity and phase composition of TiO2: a smart way to enhance biomimetic response.

This contribution sheds light on the role of crystal size and phase composition in inducing biomimetic apatite growth on the surface of nanostructured titania films synthesized by reactive magnetron sputtering of Ti targets in Ar+O(2) plasmas. Unlike most existing techniques, this method enables one to deposit highly crystalline titania films with a wide range of phase composition and nanocrystal size, without any substrate heating or postannealing. Moreover, by using this dry plasma-based method one can avoid surface hydroxylation at the deposition stage, almost inevitable in wet chemical processes. Results of this work show that high phase purity and optimum crystal size appear to be the essential requirement for efficient apatite formation on magnetron plasma-fabricated bioactive titania coatings.

Apatites↗
PubMed2007

CO2 laser-induced zonation in dental enamel: a Raman and IR microspectroscopic study.

The gradient of structural alteration and molecular exchange across CO(2) laser-irradiated areas in dental enamel was analyzed by Raman and attenuated total reflectance infrared microspectroscopy. The type and the degree of structural changes in morphologically distinguishable zones within the laser spot vary depending on the laser-irradiation parameters--power (1 and 3 W), treatment time (5 and 10 s), and operational mode (super pulse and continuous wave). Using higher power, irrespective of the operation mode, the enamel tissue ablates and a crater is formed. The prevalent phase at the bottom of the crater is dehydrated O(2) (2-)-bearing apatite, that is, the fundamental framework topology is preserved. Additional nonapatite calcium phosphate phases are located mainly at the slope of the laser crater. No structural transformation of mineral component was detected aside the crater rim, only a CO(3)-CO(2) exchange, which decays with the radial distance. A lower-power laser irradiation slightly roughens the enamel surface and the structural modification of enamel apatite is considerably weaker for continuous wave than for super pulse mode. Prolonged low-power laser treatment results in recrystallization, and thus structural recovering of apatite might be of clinical relevance for enamel surface treatments.

Apatites↗
PubMed2006

The in vitro bioactivity of two novel hydrophilic, partially degradable bone cements.

Composite bone cements were prepared with bioactive glasses (MgO-SiO(2)-3CaO.P(2)O(5)) of different reactivities. The matrix of these so-called hydrophilic, partially degradable and bioactive cements was composed of a starch/cellulose acetate blend and poly(2-hydroxyethyl methacrylate). The addition of 30 wt.% of glasses to this system made them bioactive in acellular medium: a dense apatite layer formed on the surface after 7 days of immersion in simulated body fluid. This was demonstrated both by microscopic and infrared spectroscopic techniques. The composition of the glass and, consequently, its structure was found to have important effects on the rate of the apatite formation. The combination of reactivity obtained by one formulation with the hydrophilic and degradable character of these cements makes them a very promising alternative to conventional acrylic bone cements, by allowing a better stabilization of the implant and a stronger adhesion to the bone.

Apatites↗