PubMed Health⌕ Search
Home/Archive/PubMed

PubMed · 15934328

[20 rules for hard nucleus phacoemulsification].

Vlad Chercotă
View original source ↗Export metadata ↓

Abstract

The mature cataract with hard nucleus still represents one of the most difficult task for modern phacoemulsification. The author presents some practical advise concerning both less experienced and experienced surgeons.

Explore related subjects

HardnessHumansLens Nucleus, CrystallinePhacoemulsificationTreatment OutcomeEnglish AbstractJournal ArticleReview

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Vlad Chercotă. 2005. [20 rules for hard nucleus phacoemulsification].. https://pubmed.ncbi.nlm.nih.gov/15934328/

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related citations

PubMed2006

[Shock absorption of mouthguard materials--influence of temperature conditions and shore hardness on shock absorption].

PURPOSE: To consider changes in the physical properties of mouthguard materials with the change of temperature, shock-absorbing examination and Shore hardness measurement of existing MG materials and other elastic materials were carried out. METHODS: Both examinations were done under two temperature conditions: at room temperature (25 degrees C) and simulated intraoral temperature (37 degrees C). In addition, a comparative study of the relation between Shore hardness and shock absorption of the materials was made. A self-made drop impact machine was used for the shock-absorbing examination. The thickness of a sample was assumed to be 3 mm. The loading was applied by dropping 3 kinds of steel ball, phi 10 mm (4.0 g), phi 15 mm (13.7 g), and phi 20 mm (32.6 g) from a height of 60 cm. The shock absorption of all materials was compared by the maximum impact force. Shore hardness was measured based on the JIS standard. RESULTS: The shock absorption of each material showed a different tendency depending on the loading condition. Furthermore, the shock absorption of the same material showed different results depending on the temperature condition. Shore hardness measurements tended to show low values with the condition of 37 degrees C for all materials. CONCLUSION: From the relation between shock absorption and Shore hardness, it was confirmed that there is a correlation between hardness and the maximum impact force in the materials that showed shock absorption by elastic deformation. Some materials showed high shock absorption compared with existing MG materials.

Hardness↗
PubMed2006

Effect of low O2-gas transmission rate barrier films on knoop hardness and toothbrush abrasion of resin cements.

PURPOSE: To investigate the influence of utilizing films with different oxygen transmission rates (O2-GTR) on Knoop hardness and toothbrush abrasion of resin cements for luting. METHODS: Four dual-activated, composite-type resin cements, and a chemically activated PMMA-type resin cement, were used. Three different types of barrier films (Techbarrier HI, Harden Film N130, and Lix-2) were used. Resin cement was mixed and inserted into a cylindrical mold (4 mm in diameter, 3 mm in height), then chemically activated. The specimens were stored in the dark at 37 +/- 1 degrees C, 90 +/- 5%RH conditions for 1 hour. Knoop hardness on the top surface of the resin cement was measured with a microhardness tester. The top surface of specimens (8 mm in diameter, 3 mm in height) polymerized under the same conditions were used for toothbrush abrasion testing. One-way ANOVA followed by Tukey HSD test (P< 0.05) were done. RESULTS: When the cement surface was covered by low O2-GTR film, a significant increase in Knoop hardness and resistance to toothbrush abrasion was observed for the dual activated, composite-type resin cements, but not for the chemically activated PMMA type resin cement. From the results of this study, the use of low O2-GTR matrix barrier films for the dual activated, composite-type resin cements could be effective in eliminating the oxygen inhibited layer on the cement surface.

Hardness↗
PubMed2000

Torque transmission between square wire and bracket as a function of measurement, form and hardness parameters.

The aim of the study was to investigate the influence of cross section, edge geometry and structural hardness on torque transmission between square wire and bracket. For this purpose, 5 different brands of stainless steel square wire in 3 dimensions (0.016" x 0.016", 0.016" x 0.022" and 0.017" x 0.025") were inserted into edgewise brackets with a slot size of 0.018" and loaded with different torques (1 and 3 Ncm). The slot and wire geometries were analyzed by computer on ground specimens before and after loading. In addition, the Vickers hardness and micro-hardness of the unstressed and stressed metal surfaces were determined. While the slot size was very accurately maintained, the wire dimensions deviated downwards by an average of 10%. Torque transmission led to notching and bending-up phenomena on the bracket slot flanks. A torque loading of 3 Ncm increased the torque play of 0.016" x 0.022" wires by 3.6 degrees, and of 0.017" x 0.025" wires by 3.7 degrees. In the case of 0.016" x 0.016" wires, an effective torque transmission was no longer possible. The average Vickers hardness of the wires was 533 kp/mm2, and that of the brackets 145 kp/mm2. The micro-hardness in the deformation area of stressed internal slot walls increased with increasing load transmission from 204 to 338 kp/mm2. As a result of excessively small wire dimensions and plastic deformation of the brackets, a relatively large torque play occurs. Deformation and notching in the area of the internal slot walls are inconsistent with demands for recycling brackets. A standardization of bracket wire systems stating the actual torque play would be desirable.

Hardness↗