PubMed · 16380653
The source did not provide an abstract. Follow the original record for more information.
Explore connections, maps & timelines
John J Baccelli. 2005. Modified amalgam plugger for etchant application.. https://pubmed.ncbi.nlm.nih.gov/16380653/
Cite the original work for its findings. Save a collection to share your selection of sources.
KEEP EXPLORING
The structural integrity of fibrillar type I collagen is critical for effective dentin bonding. Since most noncollagenous matrix components in dentin are closely associated with collagen, we hypothesized that they may also contribute to dentin bonding. To test this hypothesis, bovine dentin was acid-etched, treated with chondroitinase ABC (C-ABC), endo-beta-galactosidase (Endo-beta), or trypsin. Controls were prepared in the same manner but without the enzymes. All control and experimental specimens were then bonded with One-Step. Bond strength data were analyzed by one-way ANOVA and Fisher's PLSD test (p < 0.05). When dentin was treated with C-ABC or trypsin, bond strengths significantly decreased for the rewetted groups (p < 0.05). The treatment with Endo-beta showed no effects on bond strengths (p > 0.05). When the treated dentin surfaces were observed under SEM, the C-ABC and trypsin treated groups revealed significant loss of collagen fibril architecture. The results indicate that chondroitin sulfate glycosaminoglycans and trypsin-digestible noncollagenous proteins play roles in maintaining the open dimensions of the collagen fibril scaffold, which is essential for optimal dentin bonding.
Although 4-META/MMA-TBB resin has adhesive properties to dentin, and has been clinically used for the bonding treatment of vertically fractured roots and apicoectomy, there has not been any investigation on the adhesion of 4-META/MMA-TBB resin to cementum. The purpose of this in vitro study was to evaluate the bonding and the sealing ability of 4-META/MMA-TBB resin to cementum. Bovine root cementum and dentin surfaces were treated with a citric acid and ferric chloride solution, and the 4-META/MMA-TBB resin was applied on the treated surfaces before testing. The microtensile bond strength and the leakage levels obtained for the cementum were almost equal to those for the dentin. In SEM and TEM observations, a hybrid layer approximately 2-3 microm in thickness was observed at the interface between the resin and the cementum. It is concluded that 4-META/MMA-TBB resin adhered to cementum via a hybrid layer on cementum, as previously reported for dentin.
This study evaluated the influence of dentin deproteinization with NaOCl on the microshear bond strength (microSBS) and the nanoleakage patterns of three dentin bonding systems (DBS). Occlusal dentin surfaces, obtained from extracted noncarious human molars, were divided into two experimental groups, according to dentin surface treatment: Group I-37% H(3)PO(4)/15s and Group II-37% H(3)PO(4)/15s + 10% NaOCl/1 min. The dentin surfaces were bonded with one of the following DBS: Scotchbond Multipurpose-SBMP, Prime & Bond NT-PB and Clearfil SE Bond-SE. After 1 week storage in water at 37 degrees C, the specimens were subjected to the microSBS test. The data were analyzed by two-way ANOVA and Student-Newman-Keuls' test (p = 0.05). The nanoleakage was evaluated using scanning electron microscopy (SEM) in backscattered electron imaging regime. No significant difference in microSBS between dentin treatments was found for SBMP. For PB, microSBS increased after NaOCl dentin treatment. SE showed a reduction in microSBS in deproteinized specimens. SEM analysis showed different nanoleakage patterns for each DBS. Irrespective of dentin treatments, all SBMP specimens showed nanoleakage. SE did not show nanoleakage with the two dentin treatments. PB showed nanoleakage within the hybrid layer only in acid-etched specimens. The influence of dentin deproteinization was dependent on the dentin bonding system formulation.