PubMed Health⌕ Search
Home/Archive/PubMed

PubMed · 17148860

Mechanical response of polyethylene tibial component using compression loading contact test: experimental and finite element analysis.

Hajer Ketata·Abdelkader Krichen·Mohamed Kharrat·Maher Dammak
View original source ↗Export metadata ↓

Abstract

An experimental apparatus has been developed to study the mechanical response of Total Knee Replacement (TKR) prosthesis under compression loading test (Tibial HDPE component and femoral Vitallium component). Analysis of experimental results indicates that the load-displacement curve depends on the initial contact location. The position of this curve varies between two curves of lower and higher stiffness. Experimental compression loading curve for femoral part resting on flat HDPE is located between the extreme curves. This result allows us to model load-displacement curve of TKR prosthesis under compression loading using femoral component resting on flat polyethylene surface. For simple contact geometry of spherical cap on flat HDPE specimen, Hertz elastic theory can be used to describe the load displacement curve for loads under 635 N. This value corresponds to the load which induces plastic flow of polyethylene. In the case of femoral component on flat HDPE specimen, Hertz elastic theory can be considered for loads under 800 N. Finite element 2D is also used to model the compression load displacement curve for femoral component resting on flat HDPE specimen. The finite element results are similar to the Hertz elastic theory analysis for compression loading under 1200 N. Damage of tibial component can be related to the critical load which induces plastic flow of polyethylene. This load depends on the contact geometry and can be estimated with the Hertz elastic theory.

Explore related subjects

Compressive StrengthFinite Element AnalysisKnee ProsthesisMaterials TestingPolyethylenesTibiaJournal Article

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Hajer Ketata, Abdelkader Krichen, Mohamed Kharrat, Maher Dammak. 2006. Mechanical response of polyethylene tibial component using compression loading contact test: experimental and finite element analysis.. https://pubmed.ncbi.nlm.nih.gov/17148860/

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related citations

PubMed2007

Depth-dependent mechanical properties of enamel by nanoindentation.

Nanoindentation has recently emerged to be the primary method to study the mechanical behavior and reliability of human enamel. Its hardness and elastic modulus were generally reported as average values with standard deviations that were calculated from the results of multiple nanoindentation testing. In such an approach, it is assumed that the mechanical properties of human enamel are constant, independent of testing parameters, like indent depth and loading rate. However, little is known if they affect the measurements. In this study, we investigated the dependence of the hardness and elastic modulus of human enamel on the indent depth. We found that in a depth range from 100 to 2000 nm the elastic moduli continuously decreased from approximately 104 to 70 GPa, and the hardnesses decreased from approximately 5.7 to 3.6 GPa. We then considered human enamel as a fiber-reinforced composite, and used the celebrated rule of mixture theory to quantify the upper and lower bounds of the elastic moduli, which were shown to cover the values measured in the current study and previous studies. Accordingly, we attributed the depth dependence of the hardness and modulus to the continuous microstructure evolution induced by the nanoindenter tip.

Compressive Strength↗
PubMed2007

Mechanical loading of rigid intramuscular implants.

Several groups are developing different versions of a new class of leadless, permanently implanted electronic devices with a size and form factor that allows them to be injected into muscles (BIONs). Their circuitry is protected from body fluids by thin-walled hermetic capsules made from rigid and brittle materials (glass or ceramic) that include feedthroughs to their electrodes. These packages experience repetitive stresses from the very contractions that they excite. We here provide a worst-case analysis of such stresses and methods for testing and validation of devices intended for such usage, along with the failure analysis and remediation strategy for a design that experienced unanticipated failures in vivo.

Compressive Strength↗
PubMed2006

Physiologically based boundary conditions in finite element modelling.

Finite element analysis has been used extensively in the study of bone loading and implant performance, such as in the femur. The boundary conditions applied vary widely, generally producing excessive femoral deformation, and although it has been shown that the muscle forces influence femoral deflections and loading, little consideration has been given to the displacement constraints. It is hypothesised that careful application of physiologically based constraints can produce physiological deformation, and therefore straining, of the femur. Joint contact forces and a complete set of muscle forces were calculated based on the geometry of the Standardised Femur using previously validated musculoskeletal models. Five boundary condition cases were applied to a finite element model of the Standardised Femur: (A) diaphyseally constrained with hip contact and abductor forces; (B) case A plus vasti forces; (C) case A with complete set of muscle forces; (D) distally constrained with all muscle forces; (E) physiological constraints with all muscle forces. It was seen that only the physiological boundary conditions, case E, produced physiological deflections (< 2.0mm) of the femoral head in both the coronal and sagittal planes, which resulted in minimal reaction forces at the constrained nodes. Strains in the mid-diaphysis varied by up to 600 micro-strain under walking loads and 1000 micro-strain under stair climbing loads. The mode of loading, as indicated by the strain profiles on the cortex also varied substantially under these boundary conditions, which has important consequences for studies that examine localised bone loading such as fracture or bone remodelling simulations.

Compressive Strength↗