PubMed Health⌕ Search
Home/Archive/PubMed

PubMed · 3818285

Actinide distribution in the human skeleton.

R L Kathren·J F McInroy·M J Swint
View original source ↗Export metadata ↓

Abstract

Radiochemical analysis of two half skeletons donated to the United States Transuranium Registry from individuals with occupationally incurred depositions, one of 241Am and the other of 239Pu, revealed an inverse proportionality between the concentration of actinide in the bone ash and the fraction of ash (or the calcium content of the ash). A similar relationship was observed in a third case suffering from osteoporosis, but the slope was shallower. These results suggest that accurate estimates of the total skeletal content of actinide can be made from radiochemical analysis of only a few bone samples.

Explore related subjects

AmericiumAutopsyBone and BonesHumansMaleMetallurgyMiddle AgedOccupational MedicinePlutoniumRadiochemistryCase ReportsJournal ArticleResearch Support, U.S. Gov't, Non-P.H.S.

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

R L Kathren, J F McInroy, M J Swint. 1987. Actinide distribution in the human skeleton.. https://doi.org/10.1097/00004032-198702000-00006

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related citations

PubMed2006

Fast neutron spectrometry and dosimetry using a spherical moderator with position-sensitive detectors.

A neutron spectrometry and dosimetry measurement system has been developed based on a different design of the divided regions for a sphere, with three position-sensitive counters. The characteristics of the measurement system have been investigated in the reference radiation fields of Am-Be and (252)Cf sources. When realistic input spectra are used for the unfolding, the overall deviations of the calculated results for four dosimetric quantities are less than +/-10%. The results of other input spectra are also discussed in this report.

Americium↗
PubMed2006

Sorption of Am(III) onto 6-line-ferrihydrite and its alteration products: investigations by EXAFS.

For the long-term performance assessment of nuclear waste repositories, knowledge about the interactions of actinide ions with mineral surfaces such as iron oxides is imperative. The mobility of released radionuclides is strongly dependent on the sorption/desorption processes at these surfaces and on their incorporation into the mineral structure. In this study the interaction of Am(III) with 6-line-ferrihydrite (6LFh) was investigated by EXAFS spectroscopy. At low pH values (pH 5.5), as well at higher pH values (pH 8.0), Am(III) sorbs as a bidentate corner-sharing species onto the surface. Investigations of the interaction of Am(III) with Fh coated silica colloids prove the sorption onto the iron coating and not onto the silica substrate. Hence, the presence of Fh, even as sediment coating, is the dominant sorption surface. Upon heating, Fh is transformed into goethite and hematite as shown by TEM and IR measurements. The results of the fit to the EXAFS data indicate the release of sorbed Am(III) at pH 5.5 during the transformation and likely a partial incorporation of Am into the Fh transformation products at pH 8.0.

Americium↗
PubMed2006

Separation of Am3+ and Eu3+ using an extraction chromatographic resin containing bis(2,4,4-trimethylpentyl)dithiophosphinic acid as the stationary phase.

Sorption of Am3+ and Eu3+ onto an extraction chromatographic resin material, prepared by impregnating purified bis(2,4,4-trimethylpentyl)dithiophosphinic acid (commercially available as Cyanex 301) into Chromosorb W, was investigated. Separation factor (S.F. = K(d,Am)/K(d,Eu)) values tend to increase in the presence of complexing agents such as thiocyanate and nitrate. In presence of 1 M NaNO3 in the aqueous phase, a S.F. value of approximately 1000 was obtained. The nature of extracted species was ascertained by carrying out the sorption studies at different aqueous phase pH. A column made from 300 mg of the resin material was used for the separation of Am3+ and Eu3+. A synthetic solution containing 1x10(5) cpm each of Am3+ and Eu3+ when loaded on to the column, >99% Eu was eluted out in 60 mL of 1 M NaNO3 at a pH of 3.2 while Am was eluted out using 5 mL of 1 M HNO3. The performance of the resin material was found to be reasonably good even after three cycles.

Americium↗