Direct pattern techniques for crown fabrication under existing removable partial.

D Wiksten

Home/Archive/PubMed

PubMed · 6999101

Direct pattern techniques for crown fabrication under existing removable partial.

D Wiksten

View original source ↗Export metadata ↓

Abstract

The source did not provide an abstract. Follow the original record for more information.

Explore related subjects

Crowns Dental Abutments Denture Design Denture, Partial, Removable Journal Article

Keep this discovery

Explore connections, maps & timelines

BibTeX RIS

D Wiksten. 1980. Direct pattern techniques for crown fabrication under existing removable partial.. https://pubmed.ncbi.nlm.nih.gov/6999101/

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related citations

PubMed1995

The dentine-bonded ceramic crown: an ideal restoration?

The principles used in the bonding of porcelain veneers may also be applied to full-coverage restorations, with such crowns luted using resin-based materials. For these full coverage restorations, dentine bonding agents, preferably of low film thickness, may be used to treat areas of exposed dentine prior to placement. These 'dentine-bonded' all-ceramic crowns may exhibit many favourable characteristics, including those of good aesthetics and peripheral blend with gingival tissues and the potential for placement on conservative preparations which may minimise the risk of pulpal damage. Indications include cases in which conventional crowns require replacement, those in which minimal preparation techniques are appropriate, and those in which there has been tooth surface loss. Contraindications include subgingival margins, extreme occlusal interferences and insufficient tooth substance for bonding. However, the longevity of these restorations is, as yet, unknown, in the absence of long-term clinical data.

Crowns↗

PubMed1995

The use of adhesively retained all-porcelain veneers during the management of fractured and worn anterior teeth: Part 2. Clinical results after 5 years of follow-up.

Twelve subjects took part in a study of the use of adhesively bonded all-porcelain restorations in the management of worn and fractured anterior teeth. A total of 54 restorations were placed in function against natural teeth, porcelain fused to metal crowns, and acrylic denture teeth. They have been assessed over up to a 5-year period for failure, wear, marginal stain and effect upon gingival status of the teeth concerned. Eleven restorations were lost to follow-up during the 5-year period. Two restorations have failed completely and four partial failures have occurred. There has been a tendency for the margins of the restorations to exhibit stain after 3-4 years in service. There has been no significant alteration in the periodontal or gingival status of the teeth involved in the study.

Crowns↗

PubMed1995

Casting shrinkage of thin-walled castings.

OBJECTIVES AND METHODS: The casting shrinkage of thin-walled castings was measured using a tungsten die method. The thickness and the surface area of the casting were simulated to those of either partial veneer crowns or complete denture frameworks. Gold alloys were cast at two different pressures (0.35 and 0.49 MPa) and the shrinkage measurement was made at different locations on the castings to investigate the effect of these factors. RESULTS: Both overall and local shrinkages were significantly influenced by size and casting pressure. These shrinkages were significantly lower for the denture-sized (DS) specimens than for the crown-sized (CS) specimens, and significantly decreased with the increase of the casting pressure. The effect of location on the local shrinkage significantly varied with the change of the other two factors, size and pressure. At the higher casting pressure, the DS specimens sustained a significantly smaller shrinkage at the margin than at the centre, whereas the CS specimens had a significantly smaller shrinkage at the centre than at the margin at the lower pressure. CONCLUSIONS: The results suggest that the casting shrinkage of a thin-walled casting is influenced by the temperature gradient in the alloy and the resultant time difference in alloy solidification as well as the volume supply of the molten alloy in the mould.

Crowns↗