PubMed Health⌕ Search

PubMed · 9027133

[Dental care using silver amalgam].

Abstract

Dental amalgam is the most widely used filling material in dentistry. In our country there are an estimated 40 million amalgam fillings in place. The mercury present in these fillings has caused health concerns over the last 160 years that amalgam has been used in decayed teeth. The fears have always proven to be unjustified and no harmful effects have ever been demonstrated in dental patients. Mercury can be found in several forms. In dentistry, only the metallic form is used, while inorganic and organic compounds are also present in the environment. The metallic form is absorbed in the human body mostly through the lungs. Once mercury reaches toxic levels inside the body, it will interfere with cell metabolism. Most important among the target organs are the brain, the liver and the kidneys. Elimination occur through urine and feces. Mercury is universally found in blood and urine. The concentration depends on absorption by air, water, nutrition, medication (including dental fillings) and occupational hazards. There are four kinds of objectives to dental amalgam: oral galvanism, toxicity, allergenicity and ecological grievances. Disorders from oral galvanism are difficult and delicate to evaluate as the actual currents are very small. Furthermore, no significant difference can be found in current intensity between patients with and without complaints. Finally patients with complaints often present other oral disorders, the treatment of which most often eliminates all complaints that could be attributed to oral galvanism. Toxicity is dose dependent. Industrial safety rules indicate that the amount of mercury absorbed from dental amalgam fillings is far below the safety level. HgB and HgU levels in patients with amalgam fillings are situated well below the acceptable levels. Allergic disorders are observed in patients with amalgam fillings but far less than expected in view of the wide spread use of dental amalgam. The problem of mercury spilling from dental amalgam fillings into the environment will be resolved by strict legislation in the near future. In this context, it can be stated that the use of dental amalgam is safe and justified. Furthermore, it is also advisable as no other material can meet the actual dental needs as efficiently as can dental amalgam.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

G Vanherle. 1996. [Dental care using silver amalgam].. https://pubmed.ncbi.nlm.nih.gov/9027133/

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related citations

Categorizing nasal septal perforations of occupational origin as cases of corrosive rhinitis.

BACKGROUND: In clinical practice a perforation of the nasal septum secondary to an occupational exposure to corrosive chemicals is not considered a sequel of rhinitis. METHODS: Relevant articles published in the last 26 years were searched and retrieved from PubMed. RESULTS: Patients with nasal septal perforations of occupational origin show a history of rhinitis with a gradual installation of symptoms and damage of the nasal mucosa progressing to ulceration and ultimately to perforation of the nasal septum. CONCLUSION: Patients with nasal septal perforations of occupational origin exhibit the clinical and histopathological features of rhinitis whereby they should be categorized as rhinitics. This rhinitis should be considered as a type of irritant-induced occupational rhinitis and classified as corrosive rhinitis.

Corrosion↗

The corrosion of nickel-titanium rotary endodontic instruments in sodium hypochlorite.

AIM: To evaluate the corrosion resistance of nickel-titanium (NiTi) endodontic rotary instruments immersed in 5.25% sodium hypochlorite (NaOCl) solution. METHODOLOGY: The corrosion performance of NiTi instruments (S1 25 mm, ProTaper Dentsplay Maillefer, Ballaigues, Switzerland) was evaluated using commercial 5.25% NaOCl solution (pH = 12.3), and the same solution partially neutralized adding H2SO4 to reach pH = 10.1. Electrochemical measurements were carried out using a potentiostat equipped with a five-channel zero resistance ammeter (ZRA) for galvanic current measurements. The instruments were sectioned into three parts (cutting part, noncutting part and shank) and degreased with acetone and rinsing with demineralized water prior to being immersed in NaOCl solution for testing. Each set of the three parts constituted one 'virtual' instrument through the ZRA, giving access to the galvanic currents that circulate between the three parts. Nine instruments were employed to check the reproducibility of the electrochemical measurements. RESULTS: The corrosion potential (E(corr)) of the NiTi alloy reached the passive domain in approximately 20 s of immersion in the solution having a pH 10.1. After this initial period the potential remained steady, indicating that stable passivation was achieved. However, at pH 12.3 no stationary state was achieved even after 6000 s of immersion time. Thus, the alloy was not stable in this medium from a corrosion point of view. CONCLUSIONS: The corrosion resistance of NiTi alloy was enhanced by lowering the pH of NaOCl solution to 10.1, which allows the system to reach the stability domain of the passivating species TiO2 and NiO2.

Corrosion↗

Corrosion resistance measurements of dental alloys, are they correlated?

OBJECTIVES: The aim was to assess in vitro the resistance to corrosion of eight commercial dental alloys by two quantitative methods, electrochemical and immersion tests, then to statistically test the hypothesis of possible correlation between the polarization resistance (R(p)) and the elemental release. METHODS: Two quantitative methods; electrochemical and immersion test, were used. From the first, after recording the OCP during 24h immersion in acidified artificial saliva (pH 2.3), R(p) was obtained using the linear polarization in anodic path and applying the Mansfeld's method. From the static immersion test, using the same test solution, the elemental release from was analysed and determined using the ICP-AES. Thereafter, the two measurements were used to plot the regression line and to determine the correlation coefficient. The significance of the correlation was tested using F-test at a confidence interval of 0.99. RESULTS: : The resistance to corrosion results obtained from the two methods were ranked and compared; an inverse relation between them was evident. Then, the obtained coefficient of correlation (R(2)) was 0.886. With the F-test at 0.99 confidence interval, the hypothesis was accepted as the calculated F was about 44 against critical F=13.7. CONCLUSION: The correlation between the two measurements, R(p) and mass loss, was proved statistically significant. This result may provide a new approach to predict the corrosion behaviour of dental alloys by firstly using the easier methods.

Corrosion↗