PubMed · 9540658
The source did not provide an abstract. Follow the original record for more information.
Explore connections, maps & timelines
W G Dickerson. 1994. Pressed ceramic restorations.. https://pubmed.ncbi.nlm.nih.gov/9540658/
Cite the original work for its findings. Save a collection to share your selection of sources.
KEEP EXPLORING
The purpose of this study was primarily to determine the feasibility of heat-pressing a mica-based glass-ceramic with the use of commercially available dental equipment, and secondly to evaluate the effect of various processing variables on the degree of crystal alignment in the pressed glass-ceramic. The hypotheses were that the mica-based glass-ceramic could be successfully heat-pressed and that some degree of crystal orientation would be obtained, depending on the processing variables. The glass composition was melted at 1400 degrees C for 2 h and cast into 12 x 60-mm rods. Ingots (10 x 12 mm) were cut from the glass rods, heat treated, and heat-pressed under various conditions. The microstructure of the pressed specimens was investigated by SEM and compared to that of heat-treated controls. The length of Vickers-induced cracks was measured on heat-pressed specimens and heat-treated controls. The results showed that mica-based glass-ceramics could be successfully pressed with the use of commercially available dental equipment. The resulting degree of crystal alignment (texture) along the direction of pressing varied between 35 +/- 6 and 79 +/- 6. There was a linear relationship between the degree of texture and the apparent aspect ratio of the mica platelets. A significant decrease in the length of the Vickers-induced cracks in the direction perpendicular to pressing was observed, associated with an increase in length in the direction of pressing.
The utility of humic acid (HA) as a surfactant for use in the electrokinetic remediation (ER) of the clayey soils containing copper(II)-oxinate (Cu(OX)(2)) was examined. A small simulator of ER was devised, which consisted of three types of artificial soils on the basis of the commercial kaolin: kaolin, kaolin + HA and kaolin + Cu(OX)(2). The layers of kaolin containing HA and Cu(OX)(2) were sandwiched between two kaolin layers. In all experiments, a constant dc voltage gradient of 2.2V/cm was applied through the soil for 30h, and the pH of the solution in the anodic chamber was maintained at 7.0. Generally, HA has a negative charge at a neutral pH. However, the HA was mainly transferred to the cathodic chamber. This shows that the driving force of the HA in the system used herein is predominantly due to electroosmotic flow. Moreover, the amount of Cu(OX)(2) removed from the clayey soils in the presence of HA was three times larger than those in the absence of HA. This can be attributed to the fact that the water solubility of Cu(OX)(2) is enhanced by the presence of HA. Thus, we conclude that HA has a potential for use as an amendment for the ER of hydrophobic chemicals, such as Cu(OX)(2).
OBJECTIVE: To demonstrate the progression of crater growth during repeated sequential application of an Er:YAG laser to enamel and dentine, monitored using X-ray microtomography (XMT). DESIGN: A single centre study in which laser craters were created in blocks cut from human enamel and/or dentine under standardised and known conditions and then studied using XMT to obtain visualisation and quantification of the effects. SETTING: University setting, UK, 2001. MAIN OUTCOME MEASURES: Success was judged by an ability to obtain useful 3D XMT reconstructions of the blocks during crater development, and to make measurements from these data. These measurements were compared with data obtained from similar studies using different measurement techniques. RESULTS: Time sequences of 2D and 3D images were obtained which demonstrated the progression of laser craters in enamel and dentine. Quantitative measurements from these data enabled values to be derived for the rate of progression of crater depth per unit energy, and the volume of hard tissue removed per unit energy. These values were compared with data derived from other studies and shown to be broadly comparable. However, the present study is unique in that these values were obtained from a series of measurements of the same craters over time. CONCLUSIONS: 3D X-ray microtomography is shown to be a useful tool for quantitative measurements in dental research. For the Er:YAG laser, the relationship of laser crater depth and volume of mineral removed to applied energy was found to be linear.