PubMed · 9788357
Pharmaceutical emulsions, dispersions, and intracellular products put homogenization to the test in professional labs.
Explore connections, maps & timelines
W D Pandolfe, J A Butrym. 1998. When is homogenization the best processing choice?. https://doi.org/10.1038/nbt1098-974
Cite the original work for its findings. Save a collection to share your selection of sources.
KEEP EXPLORING
The aim of this study was to investigate the feasibility of partially water-miscible solvents, such as benzyl alcohol, butyl lactate and triacetin, to prepare drug nanosuspensions by a solvent quenching technique. Mitotane, which possesses very poor water solubility and low bioavailability, was used as model drug. Preparation was by emulsifying an organic solution of the drug in an aqueous solution of a stabilising agent followed by rapid displacement of the solvent from the internal into the external phase, provoking solid particle formation. To verify the influence of emulsion droplet size on the drug particle size, 0.1 or 0.2% of different emulsifiers (Tween 80, caprylyl-capryl glucoside or lecithin) and different homogenisation conditions (Ultra Turrax or a high pressure homogenizer at 200 or 1000 bar for three cycles) were used. In general, emulsion droplet size decreased with high pressure homogenization and on increasing the number of cycles. The size of drug particles, obtained after adding water at a constant rate, was dependent on the droplet size in the emulsion. Drug particles of approximately 80 nm were obtained using butyl lactate, supporting the hypothesis that drug particle formation by the emulsification diffusion process involves generating regions of local supersaturation. Because of the increase in available surface area, the dissolution rate of diaultrafiltrated suspensions increased greatly compared to commercial product.
Polymerization in micellar systems is a technique which allows the preparation of ultrafine as well as coarse latex particles. This article presents a review of the current literature in the field of radical polymerization of classical monomers in micellar systems initiated by oil-soluble initiators. Besides a short introduction to some of the kinetic aspects of emulsion polymerization initiated by water-soluble initiators, we mainly focus on the kinetics and the mechanism of radical polymerization in o/w and w/o micellar systems initiated by classical oil-soluble initiators. The initiation of emulsion polymerization of an unsaturated monomer (styrene, butyl acrylate,...) by a water-soluble initiator (ammonium peroxodisulfate) is well understood. It starts in the aqueous phase and the initiating radicals enter the monomer-swollen micelle. The formed oligomeric radicals are surface active and increase the colloidal stability of the disperse system. Besides, the charged initiating radicals might experience the energetic barrier when entering the charged particle surface. The locus of initiation with oil-soluble initiators is more complex. It can partition between the aqueous-phase and the oil-phase. Besides, the surface-active oil-soluble initiator can penetrate into the interfacial layer. The dissolved oil-soluble initiator in the monomer droplet can experience the cage effect. The small fraction of the oil-soluble initiator dissolved in the aqueous phase takes part in the formation of radicals. The oligomeric radicals formed are uncharged and therefore, they do not experience the energetic barrier when entering the polymer particles. We summarize and discuss the experimental data of radical polymerization of monomers initiated by oil-soluble initiators in terms of partitioning an initiator among the different domains of the multiphase system. The inhibitor approach is used to model the formation of radicals and their history during the polymerization. The nature of the interfacial layer and the type of oil-soluble initiator including the surface active ones are related to the kinetic and colloidal parameters. The emulsifier type and reaction conditions in the polymerization are summarized and discussed.
Preparation of dry emulsions suitable for tablet processing was examined in this study. Liquid o/w-emulsions were spray dried in a laboratory spray dryer applying hydroxypropylmethylcellulose (HPMC) as a solid carrier and emulsifier. As the lipid phase, fractionated coconut oil was used. The ability of various excipients to increase the density of dry emulsions was investigated. Adding sucrose to the formulation, redispersible dry emulsions with higher density were obtained. The type of rotary atomizer did not affect the dry emulsions containing sucrose nor the rate of rotation of the atomizer applied in the spray drying process. By wet granulation, using ethanol as a binder, free-flowing and compactable dry emulsions were obtained and simultaneously the reconstitution properties were preserved. It was concluded that dry emulsions could be optimised for tablet processing by wet granulation. Tablets having a lipid content up to 20% had proper tablet properties.