PubMed Health⌕ Search

PubMed · 9894352

Changes in tropospheric composition and air quality.

Abstract

Reductions in stratospheric ozone (O3) cause increased penetration of ultraviolet-B (UV-B) radiation to the troposphere, and therefore increases in the chemical activity in the lower atmosphere (the troposphere). Tropospheric ozone levels are sensitive to local concentrations of nitrogen oxides (NOx) and hydrocarbons. Model studies suggest that additional UV-B radiation reduces tropospheric ozone in clean environments (low NOx), and increases tropospheric ozone in polluted areas (high NOx). Assuming other factors remain constant, additional UV-B will increase the rate at which primary pollutants are removed from the troposphere. Increased UV-B is expected to increase the concentration of hydroxyl radicals (OH) and result in faster removal of pollutants such as carbon monoxide (CO), methane (CH4), non-methane hydrocarbons (NMHCs), sulfur and nitrogen oxides, hydrochlorofluorocarbons (HCFCs), and hydrofluorocarbons (HFCs). Concentrations of peroxy radicals (both inorganic and organic) are expected to increase, leading to higher atmospheric levels of hydrogen peroxide (H2O2) and organic peroxides. The effects of UV-B increases on tropospheric O3, OH, methane, CO, and possibly other tropospheric constituents, while not negligible, will be difficult to detect because the concentrations of these species are also influenced by many other variable factors (e.g., emissions). Trifluoroacetic acid (TFA, CF3COOH) is produced in the atmosphere by the degradation of HCFC-123 (CF3CHCl2), HCFC-124 (CF3CHFCl), and HFC-134a (CF3CH2F), which are used as substitutes for ozone-depleting substances. The atmospheric oxidation mechanisms of these replacement compounds are well established. Reported measurements of TFA in rain, rivers, lakes, and oceans show it to be a ubiquitous component of the hydrosphere, present at levels much higher than can be explained by reported sources. The levels of TFA produced by the atmospheric degradation of HFCs and HCFCs emitted up to the year 2020 are estimated to be orders of magnitude below those of concern, and to make only a minor contribution to the current environmental burden of TFA. No significant effects on humans or the environment have been identified from TFA produced by atmospheric degradation of HCFCs and HFCs. Numerous standard short-term studies have shown that TFA has, at most, moderate toxicity.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

X Tang, S Madronich, T Wallington, D Calamari. 1998. Changes in tropospheric composition and air quality.. https://doi.org/10.1016/s1011-1344(98)00187-0

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related citations

Stochastic simulation of daily air temperature and precipitation from monthly normals in North America north of Mexico.

A simple, stochastic daily temperature and precipitation generator (TEMPGEN) was developed to generate inputs for the study of the effects of climate change on models driven by daily weather information when climate data are available as monthly summaries. The model uses as input only 11 sets of monthly normal statistics from individual weather stations. It needs no calibration, and was parameterized and validated for use in Canada and the continental United States. Monthly normals needed are: mean and standard deviation of daily minimum and maximum temperature, first and second order autoregressive terms for daily deviations of minimum and maximum temperatures from their daily means, correlation of deviations of daily minimum and maximum temperatures, total precipitation, and the interannual variance of total precipitation. The statistical properties and distributions of daily temperature and precipitation data produced by this generator compared quite favorably with observations from 708 stations throughout North America (north of Mexico). The algorithm generates realistic seasonal patterns, variability and extremes of temperature, precipitation, frost-free periods and hot spells. However, it predicts less accurately the daily probability of precipitation, extreme precipitation events and the duration of extreme droughts.

Air↗

Blends of poly(epsilon-caprolactone) and intermediate molar mass polystyrene as Langmuir films at the air/water interface.

Poly(epsilon-caprolactone)/polystyrene (PCL/PS) blends, where nonamphiphilic PS is glassy in the bulk state at the experimental temperature of 22.5 degrees C, are immiscible as Langmuir films at the air/water (A/W) interface. Surface pressure-area per monomer isotherm analyses indicate that the surface concentration of amphiphilic PCL is the only factor influencing the surface pressure below the collapse transition. For PS-rich blends, Brewster angle microscopy (BAM) studies at the A/W interface and atomic force microscopy studies on Langmuir-Schaefer films reveal that PS nanoparticle aggregates formed at very low surface pressures can form networks upon further compression. The morphologies seen in PS-rich blends (networklike rings) are consistent with a recent study of a nonamphiphilic polyhedral oligomeric silsesquioxane (POSS), octaisobutyl-POSS, blended with amphiphilic poly(dimethylsiloxane), suggesting that the nonamphiphilic PS aggregates at the A/W interface produce domains with dipole densities that differ from that of pure PCL. In all composition regimes, the amphiphilic PCL phase tends to spread and form a continuous surface layer at the A/W interface, while simultaneously improving the dispersion of nonamphiphilic PS domains. During film expansion, BAM images show a gradual change in the surface morphology from highly continuous networklike structures (PS-rich blends) to broken ringlike structures (intermediate composition) to small discontinuous aggregates (PCL-rich blends). This study provides valuable information on the morphological evolution of semicrystalline PCL-based polymer blends confined in a "two-dimensional" geometry at the A/W interface and fundamental insight into the influence of microstructure (domain size, phase-separated structures, crystalline morphology, etc.) on the interfacial properties of blends as Langmuir films.

Air↗

Prediction of air temperature for thermal comfort of people in outdoor environments.

Current thermal comfort indices do not take into account the effects of wind and body movement on the thermal resistance and vapor resistance of clothing. This may cause public health problem, e.g. cold-related mortality. Based on the energy balance equation and heat exchanges between a clothed body and the outdoor environment, a mathematical model was developed to determine the air temperature at which an average adult, wearing a specific outdoor clothing and engaging in a given activity, attains thermal comfort under outdoor environment condition. The results indicated low clothing insulation, less physical activity and high wind speed lead to high air temperature prediction for thermal comfort. More accurate air temperature prediction is able to prevent wearers from hypothermia under cold conditions.

Air↗