Biomedical subjects
Publications and source records attributed to A A Caputo.
The adhesive effects of three adhesion promoters were compared utilizing three different filled resins on acid-etched human permanent teeth. The results demonstrated a significantly greater resistance to dislodgement of resins by shear forces when an NPG-GMA type of adhesion promoter was utilized. Type of resin did not influence resin retention.
A controlled pulsating-force system for the orthodontic movement of teeth was designed and its biologic effects were examined, with the dog serving as an experimental model. This system was applied to the maxillary right second premolar while a continuous force was delivered to the maxillary left second premolar. After a 12-day experimental period in which pulsating forces were used, the amount of tooth movement and the radiographic and histologic changes were comparable to those produced by continuous force. These preliminary data indicate that forces of greater magnitude and duration will be necessary to more fully characterize the potential advantages of a pulsating orthodontic force.
The effects of wire size, lumen size, and wire type on the production of force by closed coil springs were determined. Force production was affected as follows: (1) Keeping the lumen size constant, an increase in wire size produced an increase in force. (2) Keeping the wire size constant, an increase in lumen size produced a decrease in force. (3) For a given wire size, force varied with different wire types. This study has shown that the current recommendations for the use of closed coil springs produce forces of greater magnitude than is necessary for orthodontic tooth movement. The clinician should take care to select the proper closed coil spring for specific clinical situations.
A model system was developed which recorded the intracoronal pressure during crown cementation at three locations simultaneously. Peak pressures and residual pressures were greatest with zinc phosphate cement. The zinc oxide-eugenol cement generated the smallest amount of peak and residual pressures. The polycarboxylate cement exhibited an intermediate pressure intensity. The uneven intracoronal pressure in the cement suggests a complex flow pattern capable of developing the separation of phases that earlier work reported. However, the small residual pressure indicates that these internal back pressures appear to play a limited role in preventing a complete seating of a crown.
Positive anterior rests were shown to be an essential element of design when considering stress distribution with a removable partial denture involving anterior teeth. Proximal plates often added stability and reduced stress accumulation in any one region. Distobuccal forces on the extension base adversely affected the primary canine abutment. Forces in the regions of the anterior base and central incisor abutment produced the most widespread transmission of stress throughout the arch. Greater stress throughout the arch was observed when forces were applied to the central incisor rather than to the right canine abutment. There is a need for established criteria of rest form and placement. Guidelines for using the natural crown as opposed to a positive rest seat in a restoration are needed. Continuing studies of other anterior rest forms should increasingly clarify this phase of treatment planning. The dentist should recognize the need for structural integrity in the anterior maxillary segment when designing removable partial dentures. A practical, defensible rationale for the routine use of maxillary anterior teeth as removable partial denture abutments must be established.
The retentive capacity of three preformed endodontic dowel designs was compared at two lengths and two diameters, with three different cements. The greatest single factor influencing retention of these devices was the design used. Of the types tested in this study, the most retentive were threaded, parallel-sided dowels screwed into tapped channels. Serrated, parallel-sided dowels cemented in matched cylindrical channels provided intermediate retention, and smooth-sided tapered posts were the least retentive. Another major factor in retention was the length of imbedment into dentin. An increase in dowel imbedment depth usually corresponded to increased retention. The effect of cement type was significant only with tapered dowels. Zinc phosphate cement was most retentive, carboxylate cement exhibited intermediate retention, and the epoxy cement was least retentive. For the other post designs, cement type had no significant effect on retentive capacity. Finally, variations in dowel diameter had no significant effect on retentive ability.
The effects of heat treatment on Blue Elgiloy wire and loops formed from this wire were determined. The optimum heat treatment temperature was established to be in a narrow range in the vicinity of 950 degrees F. This regimen increases the yield and ultimate strengths of this wire. Heat treatment also produced a modification of the load-deflection characteristics of the loop configuration tested. Overall, heat treatment of the wire is indicated by this study.
Intermaxillary elastics are commonly used in orthodontic treatment, yet the exact mechanism by which they effect tooth movement has been unclear. A photoelastic model was produced to stimulate this type of therapy in examples of Class II and III malocclusions. In the open situation, inter-arch activity precipitated occlusal plane rotation; counter clockwise in Class II malocclusion and clockwise in Class III. Comment is made on the force vectors involved when using intermaxillary elastics.
Tensile retentive strengths for six polycarbonate crown cementation systems were examined with use of extracted human teeth prepared with and without retentive grooves. From the results of this study, use of unfilled intermediary resins followed by polycarboxylate or zinc phosphate cements is recommended. Retentive grooves did not contribute to overall retention.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
The force-extension characteristics for a wide range of elastics were determined. It was found that (1) selection of elastics were determined. It was found that (1) selection of elastics based on 3 x lumen size will probably result in more force being generated than was previously reported, (2) there is very little difference seen in force-extension characteristics when the two manufacturers' elastics are compared, and (3) for experimental purposes, elastic testing can be done in the dry state for force-extension characteristic studies. This investigation has shown that stretching an orthodontic elastic to twice its original lumen diameter produces a force which better represents the manufacturer's expected value. Keeping these principles in mind, a more effective tooth-moving force can be realized, enabling the clinician to properly select orthodontic elastics for intra- and intermaxillary biomechanical procedures.
An effective temporary repair of fractured poreclain denture teeth involves abrasive treatment of the fractured tooth surface followed by a composite resin buildup. This study has demonstrated that the best potential retention of the composite buildup can be obtained through abrasive treatment by a course diamond stone.
This study provided the following guidelines in the selection of specific designs for overdenture abutments: 1. The Dolder bar, which exhibits more cross-arch involvement than the Zest anchor, will share the occlusal load across the arch, between the abutments and the supporting structures. 2. The posterior edentulous regions will receive some physiologic stimulation with the Dolder bar, for it shares more stress here than the Zest anchor. 3. The forces on the Dolder bar produce stress directed more apically than that from the Zest anchor. Since this force is better tolerated, use of the Dolder bar may be indicated for a short-rooted tooth with less supporting bone. 4. The greater stress concentrated around the abutment teeth by the Zest anchor makes use of this design in a tooth that is periodontally sound and has a long root structure well imbedded in supporting bone seem logical.
The results of this study showed that: 1. The design of a retainer with a mesial rest in conjunction with a buccal I-bar or a wrought-wire and cast lingual arm exhibited the most favorable distribution of vertically applied forces. 2. Retainer designs with a distal rest tend to move the clinical crown distally and the root mesially at the apex, resulting in horizontal forces in the bone. 3. Placing rests of distal-extension removable partial dentures more anteriorly provides an axis of rotation that directs applied forces in a more vertical direction. 4. The distal rest in conjunction with circumferential retainers developed greater horizontal forces within the supporting structures.
Three commercial dental amalgams of known dissimilar clinical properties were evaluated in pure blending at widely different loading rates and temperatures. Comparative data of fracture stress at 140 F rank these alloys according to their clinical fracture resistance; the phenomenon of creep may account for early marginal fracture prior to corrosion-induced fracture.