Biomedical subjects

Chuanmin Ruan

Publications and source records attributed to Chuanmin Ruan.

6 recordsLinked to original sources

PubMed2004

A staphylococcal enterotoxin B magnetoelastic immunosensor.

A magnetoelastic immunosensor for detection of staphylococcal enterotoxin B (SEB) is described. The magnetoelastic sensor is a newly developed mass/elasticity-based transducer of high sensitivity having a material cost of approximately $0.001/sensor. Affinity-purified rabbit anti-SEB antibody was covalently immobilized on magnetoelastic sensors, of dimensions 6 mm x 2 mm x 28 microm. The affinity reaction of biotin-avidin and biocatalytic precipitation are used to amplify antigen-antibody binding events on the sensor surface. Horseradish peroxidase (HRP) and alkaline phosphatase were examined as the labeled enzymes to induce biocatalytic precipitation. The alkaline phosphatase substrate, 5-bromo-4-chloro-3-indolyl phosphate (BCIP) produces a dimer, which binds tightly to the sensor surface, inducing a change in sensor resonance frequency. The biosensor demonstrates a linear shift in resonance frequency with staphylococcal enterotoxin B concentration between 0.5 and 5 ng/ml, with a detection limit of 0.5 ng/ml.

Alkaline Phosphatase↗

PubMed2004

A magnetoelastic bioaffinity-based sensor for avidin.

A magnetoelastic bioaffinity sensor coupled with biocatalytic precipitation is described for avidin detection. The non-specific adsorption characteristics of streptavidin on different functionalized sensor surfaces are examined. It is found that a biotinylated poly(ethylene glycol) (PEG) interface can effectively block non-specific adsorption of proteins. Coupled with the PEG immobilized sensor surface, alkaline phosphatase (AP) labeled streptavidin is used to track specific binding on the sensor. This mass-change-based signal is amplified by the accumulation on the sensor of insoluble products of 5-bromo-4-chloro-3-indolyl phosphate catalyzed by AP. The resulting mass loading on the sensor surface in turn shifts the resonance frequency of the magnetoelastic sensors, with an avidin detection limit of approximately 200 ng/ml.

Avidin↗

PubMed2004

A wireless, remote query glucose biosensor based on a pH-sensitive polymer.

This paper describes a wireless, remote query glucose biosensor using a ribbonlike, mass-sensitive magnetoelastic sensor as the transducer. The glucose biosensor is fabricated by first coating the magnetoelastic sensor with a pH-sensitive polymer and upon it a layer of glucose oxidase (GOx). The pH-responsive polymer swells or shrinks, thereby changing mass, respectively, in response to increasing or decreasing pH values. The GOx-catalyzed oxidation of glucose produces gluconic acid, inducing the pH-responsive polymer to shrink, which in turn decreases the polymer mass. In response to a time-varying magnetic field, a magnetoelastic sensor mechanically vibrates at a characteristic resonance frequency, the value of which inversely depends on sensor mass loading. As the magnetoelastic films are magnetostrictive, the vibrations launch magnetic flux that can be remotely detected using a pickup coil. Hence, changes in the resonance frequency of a passive magnetoelastic transducer are detected on a remote query basis, without the use of physical connections to the sensors.The sensitivity of the glucose biosensors decreases with increasing ionic strength; at physiological salt concentrations, 0.6 mmol/L of glucose can be measured. At glucose concentrations of 1-10 mmol/L, the biosensor response is reversible and linear, with the detection limit of 0.6 mmol/L corresponding to an error in resonance frequency determination of 20 Hz. Since no physical connections between the sensor and the monitoring instrument are required, this sensor can potentially be applied to in vivo and in situ measurement of glucose concentrations.

Acrylates↗

PubMed2003

Detection of viable Salmonella typhimurium by impedance measurement of electrode capacitance and medium resistance.

Three-electrode electrochemical impedance technique was investigated for detection of Salmonella typhimurium by monitoring the growth of bacteria in selenite cystine (SC) broth supplemented with trimethylamine oxide hydrochloride (TMAO.HCl) and mannitol (M). The change in the system impedance during the growth of bacteria was studied using frequency spectral scanning. It was found that the impedance at low frequencies (<10 kHz) mainly came from the double-charged layer capacitance, reflecting the changes at the electrode interface and the adsorption on the electrode surface. While at high frequencies (>10 kHz), the system impedance mainly depended on the medium resistance. The adsorption of bacteria on the electrode surface was detected by measuring low frequency impedance, and verified with Faradic impedance spectroscopy. Enumeration of S. typhimurium using a low frequency (1 Hz) capacitance measurement and a high frequency (1 MHz) resistance measurement were compared. The detection times were determined for quantitative analysis based on the growth curves of bacteria referring to either the medium resistance or electrode capacitance. The regression equations for the detection times (t(d), h) and the initial cell number (N, cells.ml(-1)) were t(d)=-1.24logN+13.4 with R(2)=0.98 and t(d)=-1.40logN+14.46 with R(2)=0.97 for the medium resistance and electrode capacitance methods, respectively.

Cell Count↗

PubMed2003

Magnetoelastic immunosensors: amplified mass immunosorbent assay for detection of Escherichia coli O157:H7.

A mass-sensitive magnetoelastic immunosensor for detection of Escherichia coli O157:H7 is described, based on immobilization of affinity-purified antibodies attached to the surface of a micrometer-scale magnetoelastic cantilever. Alkaline phosphatase is used as a labeled enzyme to the anti-E. coli O157:H7 antibody, amplifying the mass change associated with the antibody-antigen binding reaction by biocatalytic precipitation of 5-bromo-4-chloro-3-indolyl phosphate in a pH 10.0 PBS solution. The detection limit of the biosensor is 10(2) E. coli O157:H7 cells/mL. A linear change in the resonance frequency of the biosensor was found to E. coli O157:H7 concentrations ranging from 10(2) to 10(6) cells/mL.

Biosensing Techniques↗

PubMed2002

Immunobiosensor chips for detection of Escherichia coil O157:H7 using electrochemical impedance spectroscopy.

Impedance biosensor chips were developed for detection of Escherichia coli O157:H7 based on the surface immobilization of affinity-purified antibodies onto indium tin oxide (ITO) electrode chips. The immobilization of antibodies onto ITO chips was carried out using an epoxysilane monolayer to serve as a template for chemical anchoring of antibodies. The surface characteristics of chips before and after the binding reaction between the antibodies and antigens were characterized by atomic force microscopy (AFM). The patterns of the epoxysilanes monolayer, antibodies, and E. coli cells were clearly observed from the AFM images. Alkaline phosphatase as the labeled enzyme to anti-E. coli O157:H7 antibody was used to amplify the binding reaction of antibody-antigen on the chips. The biocatalyzed precipitation of 5-bromo-4-chloro-3-indolyl phosphate by alkaline phosphatase on the chips in pH 10 PBS buffer containing 0.1 M MgCl2 increased the electron-transfer resistance for a redox probe of Fe(CN)6(3-/4-) at the electrode-solution interface or the electrode resistance itself. Electrochemical impedance spectroscopy and cyclic voltammetric method were employed to follow the stepwise assembly of the systems and the electronic transduction for the detection of E. coli. The biosensor could detect the target bacteria with a detection limit of 6 x 10(3) cells/mL. A linear response in the electron-transfer resistance for the concentration of E. coli cells was found between 6 x 10(4) and 6 x 10(7) cells/mL.

Biosensing Techniques↗