Biomedical subjects

H Chua

Publications and source records attributed to H Chua.

At least 37 records · Page 2Linked to original sources

PubMed2001

Biosorption of heavy metals by bacteria isolated from activated sludge.

Twelve aerobic bacteria from activated sludge were isolated and identified. These included both Gram-positive (e.g., Bacillus) and Gram-negative (e.g., Pseudomonas) bacteria. The biosorption capacity of these strains for three different heavy metals (copper, nickel, and lead) was determined at pH 5.0 and initial metal concentration of 100 mg/L. Among these 12 isolates, Pseudomonas pseudoalcaligenes was selected for further investigation owing to its high metal biosorption capacity. The lead and copper biosorption of this strain followed the Langmuir isotherm model quite well with maximum biosorption capacity (q(max)) reaching 271.7mg of Pb2+/g of dry cell and 46.8 mg of Cu2+/g of dry cell at pH 5.0. Study of the effect of pH on lead and copper removal indicated that the metal biosorption increased with increasing pH from 2.0 to 7.0. A mutual inhibitory effect was observed in the lead-copper system because the presence of either ion affected the sorption capacity of the other. Unequal inhibitions were observed in all the nickel binary systems. The increasing order of affinity of the three metals toward P. pseudoalcaligenes was Ni < Cu < Pb. The metal biosorptive potential of these isolates, especially P. pseudoalcaligenes, may have possible applications in the removal and recovery of metals from industrial effluents.

Adsorption↗

PubMed2001

Removal and recovery of copper (II) ions by bacterial biosorption.

Studies were conducted to investigate the removal and recovery of copper (II) ions from aqueous solutions by Micrococcus sp., which was isolated from a local activated sludge process. The equilibrium of copper biosorption followed the Langmuir isotherm model very well with a maximum biosorption capacity (q(max)) of 36.5 mg of Cu2+/g of dry cell at pH 5.0 and 52.1 mg of Cu2+/g of dry cell at pH 6.0. Cells harvested at exponential growth phase and stationary phase showed similar biosorption characteristics for copper. Copper uptake by cells was negligible at pH 2.0 and then increased rapidly with increasing pH until 6.0. In multimetal systems, Micrococcus sp. exhibited a preferential biosorption order: Cu approximate to Pb > Ni approximate to Zn. There is virtually no interference with copper uptake by Micrococcus sp. from solutions bearing high concentrations of Cl-, SO4(2-), and NO3- (0-500 mg/L). Sulfuric acid (0.05 M) was the most efficient desorption medium, recovering >90% of the initial copper sorbed. The copper capacity of Micrococcus sp. remained unchanged after five successive sorption and desorption cycles. Immobilization of Micrococcus sp. in 2% calcium alginate and 10% polyacrylamide gel beads increased copper uptake by 61%. Biomass of Micrococcus sp. may be applicable to the development of potentially cost-effective biosorbent for removing and recovering copper from effluents.

Adsorption↗

PubMed2001

Production of polyhydroxybutyrate by Bacillus species isolated from municipal activated sludge.

Plastic wastes are considered to be severe environmental contaminants causing waste disposal problems. Widespread use of biodegradable plastics is one of the solutions, but it is limited by high production cost. Biologic wastewater treatment generates large quantities of biomass as activated sludge. Only a few reports focus on the potential of utilizing resident Bacillus species from activated sludge in polyhydroxbutyrate (PHB) production as well as the production of PHB from food wastes. They have attractive properties such as short generation time, absence of endotoxins, and secretion of both amylases and proteinases that can well utilize food wastes for nutrients, which can further reduce the cost of production of polyhydroxyalkanoates (PHAs). Two PHA-producing strains, HF-1 and HF-2, were isolated from activated sludge. HF-1 outperformed HF-2 in terms of growth and PHB production in hydrolyzed soy and malt wastes. The isolated bacteria was characterized by DNA sequence alignment. Cell extracts of HF-1 were also compared to Bacillus megaterium cell extracts on sodium dodecyl sulfate polyacrylamide gel electrophoresis. The biopolymers accumulated were analyzed by gas chromatography, nuclear magnetic resonance, and Fourier transform infrared methods.

Bacillus↗

PubMed2000

Degradation pathway of persistent branched fatty acids in natural anaerobic ecosystem.

Branched fatty acids (BAFs) in industrial effluents are often persistent in biological wastewater treatment systems and end up as organic contaminants in the water environment. In this study, degradation of eight characteristic BAFs in a natural anaerobic ecosystem of an eutrophic river sediment was studied in vitro by enrichment culture techniques. The anaerobic consortium, comprising of BFA-degrading and methane-producing genera, degraded BFAs with a tertiary carbon through beta-oxidation followed by methanogenesis mechanisms. The consortium could not degrade BFAs with a quaternary carbon. The degree of branching at the alpha or beta position along the carbon chain interfered with the beta-oxidation mechanisms, and hence affected the degradability of the compound.

Bacteria, Anaerobic↗

PubMed2000

A novel magnetite-immobilized cell process for heavy metal removal from industrial effluent.

The sorption and desorption of copper (II) (Cu[II]) ions from the wastewater by magnetite-immobilized cells of Pseudomonas putida 5-x with acidic pretreatment were studied. Pretreating cells with 0.6 N HCl was found to enhance greatly the adsorption capacity of biomass up to 85.6 mg/g and had no significant effect on the loss of P. putida 5-x cells during biosorbent pretreatment. The biosorption capacity to Cu2+ of magnetite-immobilized cells of P. putida 5-x harvested during various growth phases was also investigated. The experimental results illustrated that the adsorption capacity to Cu2+ of P. putida 5-x cultured in sulfate-limiting medium reached maximum during the late stationary growth phase or early death phase, and reached minimum during the log growth phase. The mechanism of copper sequestering by this type of biomass was studied via transmission electron microscopy. A degradation of the peptidoglycan layer of the cell wall was observed in the acidic pretreatment, but no further degradation appeared after the adsorption-desorption cycle. Cu(II) accumulated mostly on the surface of the cell walls and was effectively desorbed by the acidic treatment during the desorption process.

Adsorption↗

PubMed2000

Effect of food:microorganism ratio in activated sludge foam control.

Foaming is a common operational problem in activated sludge processes that often adversely affects the quality of the treated effluent. Overgrowth of the filamentous Nocardia spp. in the microbial ecosystem was previously identified as the cause of foaming. In the present study, the specific growth rate of Nocardia amarae was found to be much higher than that of nonfilamentous bacteria under food:microorganism (F:M) ratios lower than 0.5 mg of biological oxygen demand (BOD)/(mg of mixed liquor suspended solids [MLSS].d). This indicated that filamentous overgrowth may occur in normal activated sludge processes that are continually operated under the usual F:M range of 0.2-0.6 mg of BOD/(mg of MLSS.d). A novel two-component feast-fast operation (FFO) that capitalized on the sensitivity of filamentous bacteria to F:M ratio was designed to prevent and control foaming problems. The F:M ratio in the "feasting" aeration unit was 0.8 mg of BOD/(mg of MLSS.d) whereas that in the "fasting" aeration unit was 0.2 mg of BOD/(mg of MLSS.d). The FFO resulted in an overall process F:M ratio that still remained within the normal range, while avoiding prolonged exposure of the activated sludge ecosystem to an F:M ratio below 0.5 mg of BOD/(mg of MLSS.d). The FFO suppressed the overgrowth of filamentous bacteria without adversely affecting the organic treatment efficiency of the modified process.

Nocardia↗

PubMed2000

Construction of recombinant Escherichia coli strains for polyhydroxybutyrate production using soy waste as nutrient.

Construction and comparison of recombinant Escherichia coli strains harboring the polyhydroxybutyrate (PHB) operon from Ralstonia eutropha using vectors possessing different promotors, as well as the production of PHB from soy waste by the recombinant strain, are reported. The lac promotor was the most efficient on expression of the phb operon among the three promotors studied: i.e., lac promotor, T7 promotor and the normal sigma 70 promotor. The pKS/PHB was the most efficient plasmid for phb operon expression among the three plasmids used: i.e., pKS-, pAED4, and pJM9131. It was observed that isopropyl-beta-D-thiogalactopyranoside was not required for the induction of the expression of phb operon. The cell dry wt and polyhydroxyalkanoate content by E. coli XL-1 Blue (pKS/PHB) were 3.025 g/L and 27.83%, respectively.

Cupriavidus necator↗

PubMed2000

Design and performance of a fibrous bed bioreactor for odor treatment.

Biological processes have become popular for odor treatment. In this study, a novel fibrous bed bioreactor was applied for treatment of odorous gas. The column reactor was packed with spirally wound fibrous sheet material on which a consortium of microorganisms selected from activated sludge was immobilized. The first stage of this work comprised a preliminary study that aimed at investigating the feasibility of the fibrous bed bioreactor for treatment of odorous volatile fatty acids (VFAs). In this stage, the performance of a fibrous bed bioreactor at increasing mass loadings ranging from 9.7 to 104.2 g/(m3.h) was studied. VFA removal efficiencies above 90% were achieved at mass loadings up to 50.3 g/(m3.h). At a mass loading of 104.2 g/(m3.h), removal efficiency was found to be 87.7%. In the second stage of the work, the process was scaled up with design and operational considerations, namely, packing medium, process condition, and configuration selections. A trickling biofilter with synthetic fibrous packing medium was selected. It was operated under countercurrent flow of gas and liquid streams. The effects of inlet concentration and empty bed retention time on bioreactor performance were studied. The bioreactor was effective in treating odorous VFAs at mass loadings up to 32 g/(m3.h), at which VFAs started to accumulate in the recirculation liquid, indicating that the biofilm was unable to degrade all the VFAs introduced. Although VFAs accumulated in the liquid phase, the removal efficiency remained above 99%, implying that the biochemical reaction rate, rather than gas-to-liquid mass transfer rate, was the limiting factor of this process. The bioreactor was stable for long-term operation; no clogging and degeneration of the packing medium was observed during the 4-mo operation.

Bioreactors↗

PubMed2000

Effects of trace levels of copper, chromium, and zinc ions on the performance of activated sludge.

The effects of copper, chromium, and zinc ions, at trace levels, on the performance of a simulated activated sludge process were investigated. The results of batch adsorption experiments showed that the adsorption of copper, chromium, and zinc ions followed both the Langmuir and Freundlich isotherms. The presence of trace levels of these three metals not only reduced the adsorption rate of organic matters but also the chemical oxygen demand adsorption capacity (CAC) of the activated sludge. Metal ions competed with the organic substrate for adsorption binding sites on the surfaces of activated sludge bioflocs and reduced the CAC. Studies performed in a sequential batch reactor (SBR) showed that the presence of trace levels of heavy metal ions in wastewater affected the SBR performance to different extents depending on the hydraulic retention time (HRT). When the reactors were operated at short HRTs of 2.5 d or less, the presence of trace levels of heavy metal ions reduced substantially the CAC of activated sludge, which, in turn, affected significantly the performance of the SBR. However, under longer HRTs (e.g., 5 d), the heavy metal ions in the wastewater reduced the CAC but had no significant effect on the chemical oxygen demand removal efficiency.

Adsorption↗

PubMed2000

Microbial production of polyhydroxyalkanoates by bacteria isolated from oil wastes.

A Gram-positive coccus-shaped bacterium capable of synthesizing higher relative molecular weight (M(r)) poly-hydroxybutyrate (PHB) was isolated from sesame oil and identified as Staphylococcus epidermidis (by Microbial ID, Inc., Newark, NJ). The experiment was conducted by shake flask fermentation culture using media containing fructose. Cell growth up to a dry mass of 2.5 g/L and PHB accumulation up to 15.02% of cell dry wt was observed. Apart from using single carbohydrate as a sole carbon source, various industrial food wastes including sesame oil, ice cream, malt, and soya wastes were investigated as nutrients for S. epidermidis to reduce the cost of the carbon source. As a result, we found that by using malt wastes as nutrient for cell growth, PHB accumulation of S. epidermidis was much better than using other wastes as nutrient source. The final dried cell mass and PHB production using malt wastes were 1.76 g/L and 6.93% polymer/cells (grams/gram), and 3.5 g/L and 3.31% polymer/cells (grams/gram) in shake flask culture and in fermentor culture, respectively. The bacterial polymer was characterized by 1H-nuclear magnetic resonance (NMR), 13C-NMR, Fourier transform infrared, and differential scanning calorimetry. The results show that with different industrial food wastes as carbon and energy sources, the same biopolymer (PHB) was obtained. However, the use of sesame oil as the carbon source resulted in the accumulation of PHB with a higher melting point than that produced from other food wastes as carbon sources by this organism under similar experimental conditions.

Carbohydrate Metabolism↗

PubMed2000

Effect of C:N molar ratio on monomer composition of polyhydroxyalkanoates produced by Pseudomonas mendocina 0806 and Pseudomonas pseudoalkaligenus YS1.

Polyhydroxyalkanoates (PHAs) are biodegradable polymers produced by bacteria. In this study, the effect of C:N molar ratio on the monomer composition of PHAs was investigated, including medium chain length PHA produced by Pseudomonas mendocina 0806 and PHA blends consisting of monomers of 3-hydroxybutyrate and medium chain length hydroxyalkanoate produced by Pseudomonas pseudoalkaligenus YS1. It was observed that there were some fixed ranges of C:N molar ratio that affect the monomer composition of PHA independently of the substrate. For strain 0806, the ranges were C:N < 20, 20 < C:N < 200, and C:N > 200. The monomer composition was constant among these ranges when using glucose and octanoate as the sole substrate. For strain YS1, the ranges were C:N < 20, 20 < C:N < 45, and C:N > 45. These results are useful for controlling monomer composition in PHA production.

3-Hydroxybutyric Acid↗

PubMed2000

Optimal production of polyhydroxyalkanoates in activated sludge biomass.

Polyhydroxyalkanoates (PHAs) have been recognized as good candidates for biodegradable plastics, but their high price compared with conventional plastics has limited their use. In this study, activated sludge microorganisms from a conventional wastewater treatment process were induced, by controlling the carbon:nitrogen (C:N) ratio in the reactor liquor, to accumulate PHAs. In addition, an intermittent nitrogen feeding program was established to optimize the volumetric PHA productivity in a wastewater treatment process. The optimal overall polymer production yield of 0.111 g of polymer/g of carbonaceous substrate consumed was achieved under a C:N ratio of 96:1 by feeding nitrogen in the reactor liquor once every four cycles. At the same time, the amount of excess sludge generated from the wastewater treatment process was reduced by 22.9%.

Bacteria↗

PubMed1999

Sub-lethal effects of heavy metals on activated sludge microorganisms.

The effects of heavy metals, at sub-lethal concentrations, on activated sludge microbial ecosystem were investigated. Adsorption capacity and rate of copper, chromium, lead and zinc on microbial flocs were much faster than that of organic matters. Metals affected not only the adsorption rate of organic matters but also the COD adsorption capacity of the activated sludge. Effects of heavy metals, on wastewater treatment performance of a sequencing batch reactor were also studied. Metal-laden wastewater at sub-lethal levels affected the performance to different extents, depending on the hydraulic retention time. Metal ions acted as a strong competitor against the organic compounds for active sites on the bioflocs instead of acting as a toxic microbial inhibitor, thus hampering organic adsorption and affecting the COD removal efficiency under shorter HRTs.

Adsorption↗

PubMed1999

A comparative investigation on the biosorption of lead by filamentous fungal biomass.

The removal of lead from aqueous solutions by adsorption on filamentous fungal biomass was studied. Batch biosorption experiments were performed to screen a series of selected fungal strains for effective lead removal at different metal and biomass concentrations. Biosorption of the Pb2+ ions was strongly affected by pH. The fungal biomass exhibited the highest lead adsorption capacity at pH 6. Isotherms for the biosorption of lead on fungal biomass were developed and the equilibrium data fitted well to the Langmuir isotherm model. At pH 6, the maximum lead biosorption capacity of Mucor rouxii estimated with the Langmuir model was 769 mg/g dry biomass, significantly higher than that of most microorganisms. Biomass of Mucor rouxii showed specific selectivity for Pb2+ over other metals ions such as Zn2+, Ni2+ and Cu2+. This fungal strain may be applied to develop potentially cost-effective biosorbent for removing lead from effluents. The technique of scanning electron microscopy coupled with X-ray dispersion analysis shows that Pb2+ has exchanged with K+ and Ca2+ on the cell wall of Mucor rouxii, thereby suggesting ion exchange as one of the dominant mechanisms of metal biosorption for this fungal strain.

Absorption↗

PubMed1999

Accumulation of biopolymers in activated sludge biomass.

In this study, activated sludge bacteria from a conventional wastewater treatment process were induced to accumulate polyhydroxyalkanoates (PHAs) under different carbon-nitrogen (C:N) ratios. As the C:N ratio increased from 20 to 140, specific polymer yield increased to a maximum of 0.38 g of polymer/g of dry cell mass while specific growth yield decreased. The highest overall polymer production yield of 0.11 g of polymer/g of carbonaceous substrate consumed was achieved using a C:N ratio of 100. Moreover, the composition of polymer accumulated was dependent on the valeric acid content in the feed. Copolymer poly(3-hydroxybutyrate-co-3-hydroxyvalerate) [P(3HB-co-3HV)] was produced in the presence of valeric acid. The 3-hydroxyvalerate (3HV) mole fraction in the copolymer was linearly related to valeric content in the feed, which reached a maximum of 54% when valeric acid was used as sole carbon source. When the 3HV U in the polymer increased from 0-54 mol%, the melting temperature decreased from 178 degrees to 99 degrees C. Thus, the composition, and hence the mechanical properties, of the copolymer produced from activated sludge can be controlled by adjusting the mole fraction of valeric acid in the feed medium.

Journal Article↗

PubMed1999

Conversion of industrial food wastes by Alcaligenes latus into polyhydroxyalkanoates.

Broader usage of biodegradable plastics in packaging and disposable products as a solution to environmental problems would heavily depend on further reduction of costs and the discovery of novel biodegradable plastics with improved properties. As the first step in our pursuit of eventual usage of industrial food wastewater as nutrients for microorganisms to synthesise environmental-friendly bioplastics, we investigated the usage of soya wastes from a soya milk dairy, and malt wastes from a beer brewery plant as the carbon sources for the production of polyhydroxyalkanoates (PHA) by selected strain of microorganism. Bench experiments showed that Alcaligenes latus DSM 1124 used the nutrients from malt and soya wastes to biosynthesise PHAs. The final dried cell mass and specific polymer production of A. latus DSM 1124 were 32g/L and 70% polymer/cells (g/g), 18.42 g/L and 32.57% polymer/cell (g/g), and 28 g/L and 36% polymer/cells (g/g), from malt waste, soya waste, and from sucrose, respectively. These results suggest that many types of food wastes might be used as the carbon source for the production of PHA.

Journal Article↗

PubMed1999

Performance of fibrous bed bioreactor for treating odorous gas. Scientific note.

A fibrous bed bioreactor was used for treatment of odorous volatile fatty acid (VFA). The effect of gaseous VFA (acetic, propionic, and butyric acids) mass loading on the bioreactor performance was investigated. The VFA degrading microbial culture was selected from activated sludge by the three VFAs using a shake-flask culture. The selected microorganisms were then immobilized in a biofilter using cotton fabric as packing material. In the biofiltration experiment, the inlet gas flow rates ranged from 1 to 4 L/min, the total VFA concentrations ranged from 0.10 to 0.43 g/m3, and the resulting total mass loadings of VFA studied ranged from 9.7 to 104.3 g/m3/h. At total mass loading of 104.3 g/m3/h, the VFA removal efficiency was 87.7%. Higher removal efficiencies (>90%) were achieved at mass loadings below 50.3 g/m3/h.

Journal Article↗

PubMed1998

Accumulation of biodegradable copolyesters of 3-hydroxy-butyrate and 3-hydroxyvalerate in Alcaligenes eutrophus.

Biodegradable copolyesters of 3-hydroxybutyrate-co-3-hydroxyvalerate (3HB-3HV) were produced by Alcaligenes eutrophus in a two-staged process, namely growth stage and nitrogen-deficient polyester-accumulation stage. When C5 was used as the sole carbon source, the copolyester contained 43 mol % of 3HV. A range of copolyesters with 0-43 mol % of 3HV could be produced by using a medium containing different concentration ratios of butyric acid C4 and C5. Tm of PHB homopolymer was 177.6 degrees C and that of copolyester with highest 3HV mol fraction of 43% was 99.0 degrees C. C5 concentration in the medium could be an effective means to control the polymeric composition and mechanical properties of the copolyesters accumulated in A. eutrophus.

3-Hydroxybutyric Acid↗