PubMed Health⌕ Search

Biomedical subjects

Lo Gorton

Publications and source records attributed to Lo Gorton.

At least 37 records · Page 2Linked to original sources
PubMed2005

Electrochemical redox transformations of T1 and T2 copper sites in native Trametes hirsuta laccase at gold electrode.

Mediatorless, electrochemically driven, redox transformations of T1 (type 1) and T2 copper sites in Trametes hirsuta laccase were studied by cyclic voltammetry and spectroelectrochemical redox titrations using bare gold electrode. DET (direct electron transfer) between the electrode and the enzyme was observed under anaerobic conditions. From analysis of experimental data it is concluded that the T2 copper site is in DET contact with gold. It was found that electron transfer between the gold surface and the T1 copper site progresses through the T2 copper site. From EPR measurements and electrochemical data it is proposed that the redox potential of the T2 site for high-potential 'blue' laccase is equal to about 400 mV versus NHE (normal hydrogen electrode) at pH 6.5. The hypothesis that the redox potentials of the T2 copper sites in low- and high-potential laccases/oxidases from totally different sources might be very similar, i.e. approx. 400 mV, is discussed.

Amino Acid Sequence↗
PubMed2005

Direct electrochemistry of heme multicofactor-containing enzymes on alkanethiol-modified gold electrodes.

Direct electrochemistry of heme multicofactor-containing enzymes, e.g., microbial theophylline oxidase (ThOx) and D-fructose dehydrogenase (FDH) from Gluconobacter industrius was studied on alkanethiol-modified gold electrodes and was compared with that of some previously studied complex heme enzymes, specifically, cellobiose dehydrogenase (CDH) and sulphite oxidase (SOx). The formal redox potentials for enzymes in direct electronic communication varied for ThOx from -112 to -101 mV (vs. Ag|AgCl), at pH 7.0, and for FDH from -158 to -89 mV, at pH 5.0 and pH 4.0, respectively, on differently charged alkanethiol layers. Direct and mediated by cytochrome c electrochemistry of FDH correlated with the existence of two active centres in the protein structure, i.e., the heme and the pyrroloquinoline quinone (PQQ) prosthetic groups. The effect of the alkanethiols of different polarity and charge on the surface properties of the gold electrodes necessary for adsorption and orientation of ThOx, FDH, CDH and SOx, favourable for the efficient electrode-enzyme electron transfer reaction, is discussed.

Adsorption↗
PubMed2005

Direct electron transfer reactions of laccases from different origins on carbon electrodes.

Electrochemical studies of laccases from basidiomycetes, i.e., Trametes hirsuta, Trametes ochracea, Coriolopsis fulvocinerea, Cerrena maxima, and Cerrena unicolor, have been performed. Direct (mediatorless) electrochemistry of laccases on graphite electrodes has been investigated with cyclic voltammetry, square wave voltammetry as well as potentiometry. For all mentioned high potential laccases direct electron transfer (DET) has been registered at spectrographic graphite and highly ordered pyrolytic graphite electrodes. The characteristics of DET reactions of the enzymes were analysed under aerobic and anaerobic conditions. It is shown that the T1 site of the laccase is the primary electron acceptor, both in solution (homogenous case) and at surface of the graphite electrode (heterogeneous case). A mechanism of ET for the process of the electro-reduction of oxygen at the laccase-modified graphite electrodes is proposed and the similarity of this heterogeneous process to the laccase catalysed oxygen reduction homogeneous reaction is concluded.

Basidiomycota↗
PubMed2004

Direct electron transfer between copper-containing proteins and electrodes.

The electrochemistry of some copper-containing proteins and enzymes, viz. azurin, galactose oxidase, tyrosinase (catechol oxidase), and the "blue" multicopper oxidases (ascorbate oxidase, bilirubin oxidase, ceruloplasmin, laccase) is reviewed and discussed in conjunction with their basic biochemical and structural characteristics. It is shown that long-range electron transfer between these enzymes and electrodes can be established, and the mechanistic schemes of the DET processes are proposed.

Adsorption↗
PubMed2004

Direct heterogeneous electron transfer of theophylline oxidase.

Direct electron transfer (DET) was shown between the heme containing enzyme theophylline oxidase (ThO) and the surface of both graphite and gold electrodes. As proof on graphite a steady state current for theophylline was recorded using the electrode modified with adsorbed ThO. The electrode showed a Michaelis-Menten-like response to theophylline with a detection limit of 0.2 mM and a Michaelis-Menten constant equal to 3.2 mM. These initial results open up a possibility for the development of reagentless third generation biosensor based on heterogeneous DET between ThO and an electrode. On gold DET between ThO and the surface of aldrithiol modified gold was studied with spectroelectrochemical measurements. DET was observed for soluble ThO as a change of its spectrum in a gold capillary responding to a change in the applied potential. It was shown that the redox conversion of the heme domain of the enzyme is directly (mediatorlessly) driven by the potential applied at the gold electrode. The measurements enabled an estimation of the formal potential (E degrees ') of the redox process equal to -275 +/- 50 mV versus Ag|AgClsat at pH 7.0. The experimentally determined number of the electrons involved in this heterogeneous electron transfer process was estimated to be equal to 0.53. The low precision in determination of the E degrees ' and the value of the number of electrons lower than one indicate that kinetic restrictions disturbed the evaluation of the true thermodynamic values from relatively fast spectroelectrochemical measurements.

Biosensing Techniques↗
PubMed2004

Biosensor based on cellobiose dehydrogenase for detection of catecholamines.

A cellobiose dehydrogenase (CDH)-modified graphite electrode was designed for amperometric detection of catecholamines in the flow injection mode, by their recycling between the graphite electrode (+300 mV vs Ag|AgCl) and the reduced FAD cofactor of adsorbed CDH, resulting in an amplified response signal. The high efficiency of the enzyme-catecholamine reaction leads to a detection limit below 1 nM and a sensitivity of 15.8 A.M(-1) x cm(-2) (approximately 1150 nA/microM) for noradrenaline, with a coverage of less than 2.5 microg of CDH adsorbed on the electrode surface (0.073 cm(2)). Working parameters such as pH, cellobiose concentration, carrier buffer, and applied potential were optimized, using hydroquinone as a model analyte. The sensitivity, linear range, and amplification factor can be modulated by the steady-state concentration of cellobiose in the flow buffer. The response of the sensor decreases only 2% when run continuously for 4 h in the flow injection mode. The response peak maximum is obtained within 6 s at a flow rate of 0.5 mL/min, representing the time of the entire sample segment to pass the electrode. CDH enzymes from Phanerochaete chrysosporium and Sclerotium rolfsii were investigated, providing different characteristics of the sensor, with sensors made with CDH from P. chrysosporium being the better ones.

Biosensing Techniques↗
PubMed2004

Liquid chromatography-mass spectrometry analysis of enzyme-hydrolysed carboxymethylcellulose for investigation of enzyme selectivity and substituent pattern.

A series of celloendoglucanases: Bacillus agaradhaerens Cel 5a, Humicola insolens Cel 5a, H. insolens Cel 7b, H. insolens Cel 45a, Trichoderma reesei Cel 7b, and T. reesei Cel 45a were used to hydrolyse carboxymethylcellulose (CMC) and the hydrolysis products were investigated with a novel liquid chromatography-mass spectrometry (LC-MS) method. Separation was achieved using a graphitised carbon chromatographic column which allowed the use of electrospay compatible eluents. Analysis of the compounds produced during enzyme hydrolysis of CMC is used to understand enzyme selectivities and substitution pattern of CMC. Conventional high-performance anion-exchange chromatography (HPAEC)-pulsed amperometric detection (PAD), size-exclusion chromatography (SEC)-refractive index (RI) detection, and reducing end analysis are also used to analyse enzyme-hydrolysed CMC. The LC-MS method presented allows for a more detailed investigation of hydrolysis products, which facilitates characterisation of both enzymes and substrates.

Carboxymethylcellulose Sodium↗
PubMed2004

Fermentation of seeds of Teff (Eragrostis teff), grass-pea (Lathyrus sativus), and their mixtures: aspects of nutrition and food safety.

Fermentation of pure teff (Eragrostis teff), pure grass-pea (Lathyrus sativus), and their mixtures, 9:1 and 8:2 (teff/grass-pea) has been done at two temperatures (room temperature and 35 degrees C) in duplicate using the strains of Lactobacillus plantarum, for bacterial fermentation, and Aspergillus oryzae and Rhizopus oligosporus in succession for solid-state fungal fermentation as inocula. In addition, the natural or spontaneous and back-slopping methods of bacterial fermentation have been done on the above four substrate groups. The pH and essential amino acid profiles of the different fermentation processes were compared. The back-slopping in teff at a temperature of 35 degrees C gave the sharpest pH drop. All fermentations done at 35 degrees C showed a steeper slope in their pH versus time plot compared to their room temperature counterpart. Fungal fermentation gave an improved amino acid profile for the essential ones in all of the substrate groups, except in pure grass-pea. Fermented teff/grass-pea (8:2) in this fungal fermentation has been found to be quite comparable in essential amino acid profile to an ideal reference protein recommended for children of 2-5 years of age. None of the bacterial fermentations produced a net change in their essential amino acid profile in any of the substrate groups investigated. Solid state fungal fermentation on pure grass-pea using the fungal strains R. oligosporous and A. oryzae in succession has shown that the neurotoxin beta-N-oxalyl-alpha,beta-diaminopropionic acid (beta-ODAP) in grass-pea has been removed by 80% on average for the high-toxin variety and by up to 97% for the low-toxin variety as determined by an improved chromatographic method with bioelectrochemical detection coupled on-line with refractive index detection.

Amino Acids↗
PubMed2003

Enzyme-aided investigation of the substituent distribution in cationic potato amylopectin starch.

The distribution of substituents along the polymer chain in cationic potato amylopectin starch, modified in solution, granular slurry, or dry state, was investigated. The starch derivatives were successively hydrolyzed by different enzymes, followed by characterization of the hydrolysis products obtained by means of electrospray mass spectrometry (ESI-MS) and matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS). ESI-MS and MALDI-MS were proved to be appropriate techniques for identification of the substituted hydrolysis products, for which there are no standard compounds available. No highly substituted oligomers were found in the hydrolysates, which was taken as an indication of a more or less homogeneous distribution of cationic groups in the amylopectin molecules. Furthermore, from the results obtained it was suggested that the enzymes cleave glucosidic linkages only between unsubstituted glucose units and, preferentially, linkages in sequences containing more than two adjacent unsubstituted units. The determination of the amount of unsubstituted glucose produced from every successive hydrolysis step revealed slight differences between the different starch samples with respect to the homogeneity of the substitution pattern. Among the three samples under investigation, starch cationized in solution was found to have the most and dry-cationized starch the least homogeneous distribution of substituents.

Amylopectin↗
PubMed2003

Direct electron transfer of heme- and molybdopterin cofactor-containing chicken liver sulfite oxidase on alkanethiol-modified gold electrodes.

Direct heterogeneous electron transfer (ET) of sulfite oxidase (SOx), a heme- and molybdopterin cofactor-containing intermembrane enzyme, was studied on alkanethiol-modified Au electrodes both with SOx entrapped between the modified Au electrode and a permselective membrane and with SOx adsorbed at the electrode surface, in the absence of any membrane. SOx in direct electronic communication with the electrode surface gave a quasi-reversible electrochemical signal with a midpoint potential of--120 mV vs Ag/AgCl corresponding to the redox transformations of the heme domain of SOx and with a heterogeneous ET constant in the order of 15 s(-1). The efficiency of the bioelectrocatalytic 2e- oxidation of sulfite catalyzed by SOx in direct ET exchange with the electrode was shown to depend essentially on the nature of the alkanethiol layer. Adsorption and orientation of SOx on an 11-mercapto-1-undecanol (MuD-OH) self-assembled monolayer, i.e., terminally functionalized with OH groups, provided efficient catalytic oxidation of sulfite, contrary to nonfunctionalized alkanethiols, e.g., 1-decanethiol, or alkanethiol layers terminally functionalized with NH2 groups. Comparative studies with short-chain alkanethiols, e.g., cysteamine and 2-mercaptoethanol, revealed an evidently different mode of adsorption of SOx on these layers, onto which SOx was not catalytically active. Coadsorption of MuD-OH and 11-mercapto-1-undecanamine improved the surface properties of the SAM, resulting in a higher surface coverage with bioelectrocatalytically active SOx but not in an increased apparent catalytic rate constant, kcat, ranging in the order of 18-24 s(-1) at pH 7.4. The achieved efficiency of SOx bioelectrocatalysis in direct ET reaction between the modified electrode and the enzyme approached the rates characteristic for the catalysis mediated by cytochrome c, the natural redox partner of SOx, thus implying the retention of the biological function of SOx under the heterogeneous electrode reaction conditions. Results obtained enable the development of a third-generation biosensor for sulfite monitoring.

Animals↗
PubMed2003

Improved selectivity of microbial biosensor using membrane coating. Application to the analysis of ethanol during fermentation.

A ferricyanide mediated microbial biosensor for ethanol detection was prepared by surface modification of a glassy carbon electrode. The selectivity of the whole Gluconobacter oxydans cell biosensor for ethanol determination was greatly enhanced by the size exclusion effect of a cellulose acetate (CA) membrane. The use of a CA membrane increased the ethanol to glucose sensitivity ratio by a factor of 58.2 and even the ethanol to glycerol sensitivity ratio by a factor of 7.5 compared with the use of a dialysis membrane. The biosensor provides rapid and sensitive detection of ethanol with a limit of detection of 0.85 microM (S/N=3). The selectivity of the biosensor toward alcohols was better compared to previously published enzyme biosensors based on alcohol oxidase or alcohol dehydrogenases. The biosensor was successfully used in an off-line monitoring of ethanol during batch fermentation by immobilized Saccharomyces cerevisiae cells with an initial glucose concentration of 200 g l(-1).

Biofilms↗
PubMed2003

Sensor and biosensor based on Prussian Blue modified gold and platinum screen printed electrodes.

Gold (Au) and platinum (Pt) screen-printed electrodes were modified with Prussian Blue (PB) for the development of amperometric sensors selective for hydrogen peroxide detection. The sensors exhibited sensitivities towards H(2)O(2) equal to 2 A M(-1) cm(-2) for Au and 1 A M(-1) cm(-2) for Pt electrodes. The sensors were also employed as the basis for construction of glucose biosensors through further modification with crystallised glucose oxidase immobilised in a Nafion membrane. In order to improve the operational stability of the modified electrodes a buffer solution containing tetrabutylammonium toluene-4-sulfonate was used. The long-term performance of the sensors and biosensors were evaluated by continuous monitoring of hydrogen peroxide and glucose solutions (50 microM and 1 mM, respectively) in the flow-injection mode for 10 h.

Biosensing Techniques↗
PubMed2003

Limits for alkaline detoxification of dilute-acid lignocellulose hydrolysates.

In addition to fermentable sugars, dilute-acid hydrolysates of lignocellulose contain compounds that inhibit fermenting microorganisms, such as Saccharomyces cerevisiae. Previous results show that phenolic compounds and furan aldehydes, and to some extent aliphatic acids, act as inhibitors during fermentation of dilute-acid hydrolysates of spruce. Treatment of lignocellulose hydrolysates with alkali, usually in the form of overliming to pH 10.0, has been frequently employed as a detoxification method to improve fermentability. A spruce dilute-acid hydrolysate was treated with NaOH in a factorial design experiment, in which the pH was varied between 9.0 and 12.0, the temperature between 5 and 80 degrees C, and the time between 1 and 7 h. Already at pH 9.0, >25% of the glucose was lost when the hydrolysate was treated at 80 degrees C for 1 h. Among the monosaccharides, xylose was degraded faster under alkaline conditions than the hexoses (glucose, mannose, and galactose), which, in turn, were degraded faster than arabinose. The results suggest that alkali treatment of hydrolysates can be performed at temperatures below 30 degrees C at any pH between 9.0 and 12.0 without problems with sugar degradation or formation of inhibiting aliphatic acids. Treatment with Ca(OH)2 instead of NaOH resulted in more substantial degradation of sugars. Under the harsher conditions of the factorial design experiment, the concentrations of furfural and 5-hydroxymethylfurfural decreased while the total phenolic content increased. The latter phenomenon was tentatively attributed to fragmentation of soluble aromatic oligomers in the hydrolysate. Separate phenolic compounds were affected in different ways by the alkaline conditions with some compounds showing an increase in concentration while others decreased. In conclusion, the conditions used for detoxification with alkali should be carefully controlled to optimize the positive effects and minimize the degradation of fermentable sugars.

Calcium Hydroxide↗
PubMed2002

Immobilization of peroxidase glycoprotein on gold electrodes modified with mixed epoxy-boronic Acid monolayers.

The development of bioelectronic enzyme applications requires the immobilization of active proteins onto solid or colloidal substrates such as gold. Coverage of the gold surface with alkanethiol self-assembled monolayers (SAMs) reduces nonspecific adsorption of proteins and also allows the incorporation onto the surface of ligands with affinity for complementary binding sites on native proteins. We present in this work a strategy for the covalent immobilization of glycosylated proteins previously adsorbed through weak, reversible interactions, on tailored SAMs. Boronic acids, which form cyclic esters with saccharides, are incorporated into SAMs to weakly adsorb the glycoprotein onto the electrode surface through their carbohydrate moiety. To prevent protein release from the electrode surface, we combine the affinity motif of boronates with the reactivity of epoxy groups to covalently link the protein to heterofunctional boronate-epoxy SAMs. The principle underlying our strategy is the increased immobilization rate achieved by the weak interaction-induced proximity effect between slow reacting oxyrane groups in the SAM and nucleophilic residues from adsorbed proteins, which allows the formation of very stable covalent bonds. This approach is exemplified by the use of phenylboronates-oxyrane mixed monolayers as a reactive support and redox-enzyme horseradish peroxidase as glycoprotein for the preparation of peroxidase electrodes. Quartz crystal microbalance, atomic force microscopy, and electrochemical measurements are used to characterize these enzymatic electrodes. These epoxy-boronate functional monolayers are versatile, stable interfaces, ready to incorporate glycoproteins by incubation under mild conditions.

Adsorption↗
PubMed2002

Supercritical fluid extraction of a lignocellulosic hydrolysate of spruce for detoxification and to facilitate analysis of inhibitors.

This work describes a novel approach to detoxify lignocellulosic hydrolysates and facilitate the analysis of inhibitory compounds, namely supercritical fluid extraction (SFE). The efficiency of the fermentation of lignocellulosic dilute-acid hydrolysates depends upon the composition of the hydrolysate and the organism used. Furthermore, it has been shown that inhibitors in the hydrolysate reduce the fermentation yield. This knowledge has given rise to the need to identify and remove the inhibiting compounds. Sample clean-up or work-up steps, to provide a clean and concentrated sample for the analytical system, facilitate the characterization of inhibitors, or indeed any compound in the hydrolysates. Removal of inhibitors was performed with countercurrent flow supercritical fluid extraction of liquid hydrolysates. Three different groups of inhibitors (furan derivatives, phenolic compounds, and aliphatic acids) and sugars were subsequently analyzed in the hydrolysate, extracted hydrolysate, and extract. The effect of the SFE treatment was examined with respect to fermentability with Saccharomyces cerevisiae. Not only did the extraction provide a clean and concentrated sample (extract) for analysis, but also a hydrolysate with increased fermentability as well as lower concentrations of inhibitors such as phenolics and furan derivatives.

Bioreactors↗
PubMed2002

Effect of different forms of alkali treatment on specific fermentation inhibitors and on the fermentability of lignocellulose hydrolysates for production of fuel ethanol.

Treatment with alkali, particularly overliming, has been widely used as a method for the detoxification of lignocellulose hydrolysates prior to ethanolic fermentation. However, the mechanisms behind the detoxification effect and the influence of the choice of cation have not been well understood. In this study, a dilute acid hydrolysate of spruce and an inhibitor cocktail consisting of six known inhibitors were used to investigate different alkali detoxification methods. The various treatments included the addition of calcium hydroxide, sodium hydroxide, potassium hydroxide, and ammonia to pH 10.0 and subsequent adjustment of the pH to 5.5 with either sulfuric or hydrochloric acid as well as treatment with the corresponding amounts of calcium, sodium, and potassium as sulfate or chloride salts at pH 5.5. An RP-HPLC method was developed for the separation of 18 different inhibitors in the hydrolysate, including furaldehydes and phenolics. Detection and quantification were carried out by means of UV, DAD, and ESI-MS in negative mode. Treatment of the spruce hydrolysate with alkali resulted in up to approximately 40% decrease in the concentration of furaldehydes. The effects on the aromatic compounds were complex. Furthermore, SFE was performed on the precipitate formed during alkali treatment to evaluate the inhibitor content of the precipitate, and the following RP-HPLC analysis implied that potential inhibitors were removed mainly through conversion rather than through filtration of precipitate. Parallel experiments in which sulfuric acid or hydrochloric acid was used for acidification to pH 5.5 after alkali treatment indicated that the choice of anion did not affect the removal of inhibitors. Detoxification with calcium hydroxide and ammonia resulted in better fermentability using Saccharomyces cerevisiae than detoxification with sodium hydroxide. The results from the experiments with the inhibitor cocktail indicated that the positive effects of alkali treatment are difficult to explain by removal of the inhibitors only and that possible stimulatory effects on the fermenting organism warrant further attention.

Acetic Acid↗
PubMed2002

Effect of cysteine mutations on direct electron transfer of horseradish peroxidase on gold.

Surface exposed cysteines were genetically engineered in the structure of recombinant horseradish peroxidase (rHRP). Recombinant forms of HRP with either a His-tag or a Strep-tag at the C-terminus were produced, which additionally had cysteines at positions 57, 189 or 309 (C-terminus) of the polypeptide chain. An E. coli expression system was exploited. The effect of these mutations on the direct electron transfer (ET) between Au and the enzyme was studied in the reaction of the bioelectrocatalytic reduction of H(2)O(2), at -50 mV versus Ag/AgCl, on rHRP-modified Au electrodes placed in a wall-jet flow-through electrochemical cell. Adsorptive immobilisation of rHRPs on pre-oxidised Au from the protein solution at pH 6.0 provided a high and stable current response to H(2)O(2) due to its bioelectrocatalytic reduction based on direct (mediatorless) ET between Au and the active site of the rHRPs. Comparative analysis of the direct ET rate constants, estimated from the amperometric data on direct and mediated ET in the presence of catechol at pH 7.4 and 6.0, gave evidence that the introduction of the His-tag or cysteine in the C-terminal area of the enzyme resulted in an increased efficiency of direct ET due to a favourable coupled electron and proton transfer pathway. Due to the high efficiency of direct ET, the sensitivity was independent on the addition of the mediator or change of pH indicating that the response to H(2)O(2) is determined solely by the mass transfer of the analyte to the active site of HRP. The sensitivities obtained for the Au electrodes modified with rHRPs (2.0+/-0.1 A M(-1) cm(-2)) and the low detection limit for H(2)O(2) (10 nM) paves the way to develop the P-chip (peroxidase chip)--a biosensors system of a microscopic size for a mediatorless detection of H(2)O(2) based on direct ET between Au and the recombinant forms of HRP.

Biosensing Techniques↗