Biomedical subjects

Michael F Rubner

Publications and source records attributed to Michael F Rubner.

At least 19 recordsLinked to original sources

PubMed2007

Heterostructured magnetic nanotubes.

Heterostructured magnetic tubes with submicrometer dimensions were assembled by the layer-by-layer deposition of polyelectrolytes and nanoparticles in the pores of track-etched polycarbonate membranes. Multilayers composed of poly(allylamine hydrochloride) and poly(styrene sulfonate) assembled at high pH (pH > 9.0) were first assembled into the pores of track-etched polycarbonate membranes, and then multilayers of magnetite (Fe3O4) nanoparticles and PAH were deposited. Transmission electron microscopy (TEM) confirmed the formation of multilayer nanotubes with an inner shell of magnetite nanoparticles. These tubes exhibited superparamagnetic characteristics at room temperature (300 K) as determined by a SQUID magnetometer. The surface of the magnetic nanotubes could be further functionalized by adsorbing poly(ethylene oxide)-b-poly(methacrylic acid) block copolymers. The separation and release behavior of low molecular weight anionic molecules (i.e., ibuprofen, rose bengal, and acid red 8) by/from the multilayer nanotubes were studied because these tubes could potentially be used as separation or targeted delivery vehicles. The magnetic tubes could be successfully used to separate (or remove) a high concentration of dye molecules (i.e., rose bengal) from solution by activating the nanotubes in acidic solution. The release of the anionic molecules in physiologically relevant buffer solution showed that whereas bulky molecules (e.g., rose bengal) release slowly, small molecules (i.e., ibuprofen) release rapidly from the multilayers. The combination of the template method and layer-by-layer deposition of polyelectrolytes and nanoparticles provides a versatile means to create functional nanotubes with heterostructures that can be used for separation as well as targeted delivery.

Journal Article↗

PubMed2006

Two-level antibacterial coating with both release-killing and contact-killing capabilities.

Using a combination of an aqueous layer-by-layer deposition technique, nanoparticle surface modification chemistry, and nanoreactor chemistry, we constructed thin film coatings with two distinct layered functional regions: a reservoir for the loading and release of bactericidal chemicals and a nanoparticle surface cap with immobilized bactericides. This results in dual-functional bactericidal coatings bearing both chemical-releasing bacteria-killing capacity and contact bacteria-killing capacity. These dual-functional coatings showed very high initial bacteria-killing efficiency due to the release of Ag ions and retained significant antibacterial activity after the depletion of embedded Ag because of the immobilized quaternary ammonium salts.

Anti-Bacterial Agents↗

PubMed2006

pH-induced hysteretic gating of track-etched polycarbonate membranes: swelling/deswelling behavior of polyelectrolyte multilayers in confined geometry.

pH-induced hysteretic gating of track-etched polycarbonate membranes (TEPC) has been achieved by depositing layer-by-layer assembled polyelectrolyte multilayers comprising poly(allylamine hydrochloride) (PAH) and poly(sodium 4-styrenesulfonate) (PSS) at a high pH condition (pH > 9.0). Scanning electron microscopy and transmission electron microscopy showed that the average bilayer thickness of multilayers was greater within the cylindrical pores of track-etched polycarbonate membranes compared to the multilayers on planar substrates (e.g., Si wafers and the face of TEPC membranes). Swelling/deswelling properties of multilayers and gating properties of the multilayer-modified TEPC membranes were studied by measuring the flux of pH-adjusted deionized water. Large discontinuous changes in the transmembrane flux were observed, indicating that the multilayers within the cylindrical pores of TEPC membranes exhibit the discontinuous swelling/deswelling behavior observed previously for planar systems. The degree of swelling as estimated by simple models, however, showed that (PAH/PSS) multilayers in the confined geometry swelled to smaller extents compared to the same multilayers on planar substrates under the same conditions. Multilayer-modified membranes showed reversible gating properties as the pH condition of feed solution was alternated between pH 2.5 and 10.5. In situ atomic force microscopy (AFM) was used to visualize the closing of the pores as a function of time. The hysteretic gating property of the multilayer-modified TEPC membrane was utilized to achieve either a "closed" or "open" state at one pH condition depending on the pretreatment history, thereby enabling either the retention or passage of high-molecular weight polymers by varying the membrane pretreatment condition.

Journal Article↗

PubMed2006

Photo-cross-linkable polyelectrolyte multilayers for 2-D and 3-D patterning.

We report the synthesis of poly(acrylic acid-ran-vinylbenzyl acrylate) (PAArVBA), a photo-cross-linkable weak polyelectrolyte, and its incorporation into polyelectrolyte multilayer (PEM) films. PEM films assembled from PAArVBA and poly(allylamine hydrochloride) (PAH) are found to exhibit similar thickness trends with assembly pH as those previously reported for poly(acrylic acid) (PAA)/PAH multilayers. Swelling properties of the as-built and photo-cross-linked films are studied by in situ ellipsometry. Two-dimensional masking techniques are used to pattern regions of high and low swelling, as confirmed by atomic force microscopy (AFM), and to provide spatial control over the low-pH-induced microporosity transition exhibited by PAH/PAA PEMs. Films containing alternating blocks of PAH/PAArVBA bilayers and PAH/PAA bilayers were assembled, laterally photopatterned, and exposed to low-pH solution to generate nanoporosity leading to patterned Bragg reflectors, thereby demonstrating three-dimensional control over film structure in these weak PEM assemblies.

Journal Article↗

PubMed2006

Nanoporosity-driven superhydrophilicity: a means to create multifunctional antifogging coatings.

Multifunctional nanoporous thin films have been fabricated from layer-by-layer assembled silica nanoparticles and a polycation. The resultant multilayer films were found to exhibit both antifogging and antireflection properties. The antifogging properties are a direct result of the development of superhydrophilic wetting characteristics (water droplet contact angle <5 degrees within 0.5 s or less). The nearly instantaneous sheetlike wetting promoted by the superhydrophilic multilayer prevents light scattering water droplets from forming on a surface. The low refractive index of the multilayer film (as low as 1.22) resulting from the presence of nanopores was found to impart excellent antireflection properties. Glass slides coated on both sides with a nanoporous multilayer film exhibited transmission levels as high as 99.8%. Stable superhydrophilic wetting characteristics were obtained only after a critical number of bilayers were deposited onto a surface. The assembly conditions (solution pH and nanoparticle concentration), as well as the choice of nanoparticle size, were found to strongly influence film properties. It is suggested that the superhydrophilic behavior is driven by the rapid infiltration of water into a 3D nanoporous network created under specific assembly conditions.

Journal Article↗

PubMed2006

Controlled drug release from porous polyelectrolyte multilayers.

Microporous and nanoporous polyelectrolyte multilayer films have been explored as ultrathin coatings for controlled drug release. Ketoprofen and cytochalasin D were successfully loaded into nanoporous films and showed zero-order release kinetics over a period of many days. In addition to homogeneous porous multilayers, heterostructures comprising porous regions stacked alternately with nonporous regions were assembled. The heterostructures behaved as dielectric mirrors, which made it possible to optically monitor the loading process. The effects of varying the number of layers in porous and nonporous regions as well as the pore size on the drug release properties were studied. Nonporous regions in the film had no effect on the release rate or duration of release. The amount of drug released could be tuned by varying the number of layers in the porous regions of films, and the release rate depended on the pore size in the films. Microporous multilayers exhibited a Fickian diffusion of drug that was approximately twice as fast as the corresponding nanoporous films. Finally, cell culture experiments with WT NR6 fibroblasts confirmed that cytochalasin D retained its ability to inhibit mitosis after release from the multilayers.

Animals↗

PubMed2006

Biochemical functionalization of polymeric cell substrata can alter mechanical compliance.

Biochemical functionalization of surfaces is an increasingly utilized mechanism to promote or inhibit adhesion of cells. To promote mammalian cell adhesion, one common functionalization approach is surface conjugation of adhesion peptide sequences such as Arg-Gly-Asp (RGD), a ligand of transmembrane integrin molecules. It is generally assumed that such functionalization does not alter the local mechanical properties of the functionalized surface, as is important to interpretations of macromolecular mechanotransduction in cells. Here, we examine this assumption systematically, through nanomechanical measurement of the nominal elastic modulus of polymer multilayer films of nanoscale thickness, functionalized with RGD through different processing routes. We find that the method of biochemical functionalization can significantly alter mechanical compliance of polymeric substrata such as weak polyelectrolyte multilayers (PEMs), increasingly utilized materials for such studies. In particular, immersed adsorption of intermediate functionalization reagents significantly decreases compliance of the PEMs considered herein, whereas polymer-on-polymer stamping of these same reagents does not alter compliance of weak PEMs. This finding points to the potential unintended alteration of mechanical properties via surface functionalization and also suggests functionalization methods by which chemical and mechanical properties of cell substrata can be controlled independently.

Animals↗

PubMed2006

Patterned superhydrophobic surfaces: toward a synthetic mimic of the Namib Desert beetle.

The present study demonstrates a surface structure that mimics the water harvesting wing surface of the Namib Desert beetle. Hydrophilic patterns on superhydrophobic surfaces were created with water/2-propanol solutions of a polyelectrolyte to produce surfaces with extreme hydrophobic contrast. Selective deposition of multilayer films onto the hydrophilic patterns introduces different properties to the area including superhydrophilicity. Potential applications of such surfaces include water harvesting surfaces, controlled drug release coatings, open-air microchannel devices, and lab-on-chip devices.

2-Propanol↗

PubMed2006

All-nanoparticle thin-film coatings.

All-nanoparticle thin-film coatings that exhibit antireflection, antifogging (superhydrophilicity), and self-cleaning properties have been prepared via layer-by-layer deposition of TiO(2) and SiO(2) nanoparticles. The porosity and chemical composition of the coatings were determined using a simple method that is based on ellipsometry and does not require any assumptions about the refractive indices of the constituent nanoparticles. The presence of nanopores in the TiO(2)/SiO(2) nanoparticle coatings results in superhydrophilicity as well as antireflection properties. The superhydrophilicity of contaminated coatings could also be readily recovered and retained after ultraviolet irradiation.

Adsorption↗

PubMed2005

Antibacterial properties of Ag nanoparticle loaded multilayers and formation of magnetically directed antibacterial microparticles.

Antibacterial coatings based on hydrogen-bonded multilayers containing in situ synthesized Ag nanoparticles were created on planar surfaces and on magnetic colloidal particles. We report the antibacterial properties of these coatings, determined using a disk-diffusion (Kirby-Bauer) test, as a function of the film thickness and the concentration of Ag nanoparticles in the hydrogen-bonded multilayers. The zone of inhibition (ZoI) determined by the disk-diffusion test increases as the thickness of the multilayer film is increased. Results obtained for the values of the ZoI as a function of film thickness can be described adequately with a simple diffusion model (i.e., the square of the zone of inhibition (ZoI) depended linearly on the logarithm of the thickness of the silver-loaded films). This observation suggests that, in order to incrementally increase the ZoI, an exponentially increasing amount of Ag is required within the multilayers. In general, there was no statistically significant correlation between the zone of inhibition and the number of Ag loading and reduction cycles. The duration of sustained release of antibacterial Ag ions from these coatings, however, could be prolonged by increasing the total supply of zerovalent silver in the films via multiple loading and reduction cycles. These results indicate that the release of silver is controlled by an oxidation mechanism at the surface of the nanoparticles and that repeated loading and reduction of silver leads preferentially to growth of the existing silver nanoparticles in the film as opposed to nucleation of new Ag nanoparticles. We also show that magnetic microspheres coated with silver nanoparticle loaded hydrogen-bonded multilayer thin films can be used to deliver antibacterial agents to specific locations. The minimum inhibitory concentration (MIC) of nanocomposite coated microspheres was determined by the agar dilution technique: antibacterial magnetic microspheres with higher concentrations of Ag nanoparticles exhibited lower MIC values.

Acrylic Resins↗

PubMed2005

Tuning compliance of nanoscale polyelectrolyte multilayers to modulate cell adhesion.

It is well known that mechanical stimuli induce cellular responses ranging from morphological reorganization to mineral secretion, and that mechanical stimulation through modulation of the mechanical properties of cell substrata affects cell function in vitro and in vivo. However, there are few approaches by which the mechanical compliance of the substrata to which cells adhere and grow can be determined quantitatively and varied independent of substrata chemical composition. General methods by which mechanical state can be quantified and modulated at the cell population level are critical to understanding and engineering materials that promote and maintain cell phenotype for applications such as vascular tissue constructs. Here, we apply contact mechanics of nanoindentation to measure the mechanical compliance of weak polyelectrolyte multilayers (PEMs) of nanoscale thickness, and explore the effects of this tunable compliance for cell substrata applications. We show that the nominal elastic moduli E(s) of these substrata depend directly on the pH at which the PEMs are assembled, and can be varied over several orders of magnitude for given polycation/polyanion pairs. Further, we demonstrate that the attachment and proliferation of human microvascular endothelial cells (MVECs) can be regulated through independent changes in the compliance and terminal polyion layer of these PEM substrata. These data indicate that substrate mechanical compliance is a strong determinant of cell fate, and that PEMs of nanoscale thickness provide a valuable tool to vary the external mechanical environment of cells independently of chemical stimuli.

Acrylates↗

PubMed2004

Controlling cell attachment selectively onto biological polymer-colloid templates using polymer-on-polymer stamping.

A new patterning approach using polymer-on-polymer stamping (POPS) has been developed to fabricate polymer-colloid templates for controlling selective cell attachment. In this paper, a polyamine surface patterned onto a poly(acrylic acid)/poly(allylamine hydrochloride) (PAA/PAH) cell resistant multilayer platform serves as a template for the deposition of close- or loose-packed colloidal particles. Peptides containing the RGD adhesion sequence were used to modify the PAH/colloid surface for specific cell attachment. Cell behavior was studied by varying colloidal packing array density, pattern geometry, and surface chemistry. It was found that loose-packed RGD-modified colloidal arrays enhance cell adhesion, as observed through the development of focal adhesion contacts and orientation of actin stress fibers, but close-packed colloidal arrays induce a rounded and nonadhesive cell morphology and yield a smaller number of attached cells. On loose-packed arrays, cells adjust their shapes to the pattern geometry when the stripe width is smaller than 50 microm and increase their extent of attachment when the concentration of surface RGD peptides is increased. This new biomaterials system allows the examination of cell behavior as a function of RGD surface distribution on the molecular to micrometer scale and reveals cellular response to different surface roughnesses.

Acrylic Resins↗

PubMed2004

Bioinert solution-cross-linked hydrogen-bonded multilayers on colloidal particles.

Bioinert polyelectrolyte multilayers comprised of poly(acrylic acid) and polyacrylamide were deposited on colloidal particles (1.7 microm in diameter) at low pH conditions by layer-by-layer assembly using hydrogen-bonding interactions. The multilayer films were coated uniformly on the colloidal particles without causing any flocculation of the colloids, and the deposited films were subsequently cross-linked by a single treatment of a carbodiimide aqueous solution. The lightly cross-linked multilayer films show excellent stability at physiological conditions (pH 7.4, phosphate-buffered saline), whereas untreated multilayer films dissolved. The multilayer-coated surfaces, both on flat substrates and on colloidal particles, exhibit excellent resistance toward mammalian cell adhesion. With this new solution-based cross-linking method, bioinert H-bonded multilayer coatings offer potential for biomedical applications.

Acrylic Resins↗

PubMed2004

Creating effective refractive index gradients within polyelectrolyte multilayer films: molecularly assembled rugate filters.

We demonstrate the use of aqueous-based layer-by-layer (LbL) processing and in situ nanoreactor chemistry for creating polyelectrolyte multilayer (PEM) nanocomposites in which the concentration of a nanoparticle species is modulated throughout the depth of the film in a complex way. Using the in situ growth of silver nanoparticles to selectively increase the refractive index of precisely defined regions of the PEM film, we have produced a digitized rugate filter, a special type of dielectric mirror possessing many thin layers that approximate a continuous, periodic refractive index profile. The design of the digital rugate from an initial smooth index profile was aided by a computer, and construction of the device was accomplished entirely by automated means. Poly(allylamine hydrochloride) (PAH) and poly(acrylic acid) (PAA) bilayer regions within the film supported subsequent nanoreactor chemistry and created the high refractive index regions of the film, while PAH and poly(styrenesulfonate) (PSS) bilayer regions remained unmodified and served as the low index regions. Spectroscopic results obtained from the assembled device confirm the presence of a reflection band that grows in amplitude with increasing silver incorporation, reaching a peak reflectance of 75% after five silver loading and exchange cycles. The rugate structure suppresses reflection sidebands, features common to Bragg reflectors and simpler dielectric mirror designs. Cross-sectional TEM reveals nanoscale control of the size and location of silver-containing domains within the PEM film. The ability of this method to control the placement of nanoparticles within PEMs enables the inexpensive, easy production of conformable optical coatings with tunable properties. In addition, these nanocomposite films may have applications in a number of other fields where precise control of effective gradients in physical properties throughout thin films has been shown to affect the overall performance in a desirable way.

Journal Article↗

PubMed2004

Patterned and controlled polyelectrolyte fractal growth and aggregations.

Two-dimensional patterned and controlled polyelectrolyte aggregations (e.g., tree-like ramified structures) created by microcontact printing have been demonstrated and discussed. Polyelectrolyte-micropatterned aggregations on surfaces were controlled by the micropattern size and shape of PDMS stamps. The formation of aggregates was dependent on the ink and surface conditions, and the aggregates consisted of two distinct layers; strongly adsorbed, primary uniform layers and weakly adsorbed, secondary aggregation layers positioned on top of the primary layers. The adsorption of the primary layers was strong enough not to be washed away, while the aggregated secondary layers were easily removed by washing. The aggregation of secondary layers showed typical tree-like ramified structures of fractal growth and aggregation. Directional and confined stamping led to directing and confining the growth of the fractal polyelectrolyte clusters, respectively. The micropatterned primary uniform layers were not removed by extensive washing, and they were identified by selective nickel plating and charged particle selective adsorption in which the surface formed positive and negative micropatterns. These functional and patterned surfaces have great potentials for advanced devices and sensors.

Journal Article↗

PubMed2004

Controlling mammalian cell interactions on patterned polyelectrolyte multilayer surfaces.

A newly discovered class of cell resistant surfaces, specifically engineered polyelectrolyte multilayers, was patterned with varying densities of adhesion ligands to control attachment of mammalian cells and to study the effects of ligand density on cell activity. Cell adhesive patterns were created on cell resistant multilayer films composed of poly(acrylic acid) and polyacrylamide through polymer-on-polymer stamping of poly(allylamine hydrochloride) PAH and subsequent reaction of the amine functional groups with an adhesion ligand containing RGD (Arg-Gly-Asp). These cell patterns demonstrated great promise for long-term applications since they remained stable for over 1 month, unlike ethylene glycol functional surfaces. By changing the stamping conditions of PAH, it was possible to alter the number of available functional groups in the patterned regions, and as a result, control the ligand density. Cell spreading, morphology, and cytoskeletal organization were compared at four different RGD densities. The highest RGD density, approximately 152 000 molecules/microm2, was created by stamping PAH at a pH of 11.0. Lowering the stamping ink pH led to patterns with lower ligand surface densities (83 000 molecules/microm2 for pH 9.0, 53,000 molecules/ microm2 for pH 7.0, and 25 000 molecules/microm2 for pH 3.5). An increasing number of cells attached and spread as the RGD density of the patterns increased. In addition, more cells showed well-defined actin stress fibers and focal adhesions at higher levels of RGD density. Finally, we found that pattern geometry affected cytoskeletal protein organization. Well-formed focal adhesions and cell-spanning stress fibers were only found in cells on wider line patterns (at least 25 microm in width).

Acrylic Resins↗

PubMed2002

Solid-state light-emitting devices based on the tris-chelated ruthenium(II) complex. 4. High-efficiency light-emitting devices based on derivatives of the tris(2,2'-bipyridyl) ruthenium(II) complex.

Light-emitting devices from the tris(2,2'-bipyridyl)ruthenium(II) complex [Ru(bpy)(3)(2+)] and new derivatives thereof were prepared. Due to the electrochemical nature of the device operation, single-layer devices in an ITO/ Ru(bpy)(3)(2+) complex + PMMA/Ag sandwich configuration achieved very high external quantum efficiencies. The derivatives of the Ru(bpy)(3)(2+) complex were designed and synthesized to inhibit self-quenching of the excited state by adding different alkyl substituents on the bipyridyl ligands. As a result, devices that contain these new Ru(bpy)(3)(2+) complexes show a higher photoluminescence and electroluminescence efficiency than devices made from the unmodified Ru(bpy)(3)(2+) complex. External quantum efficiencies up to 5.5% at brightnesses in the range of 10-50 cd/m(2) are reported. In addition, the response time of such devices (which is a result of the electrochemical operation) has been shortened dramatically. An "instantaneous" light emission is achieved for devices that employ smaller counterions such as BF(4)(-) to increase the ionic conductivity. Such a device shows a response time of less than 1 s to emit 10-20 cd/m(2) after the operating voltage of 2.4 V has been applied.

Journal Article↗

PubMed2002

Micropatterning of polymer thin films with pH-sensitive and cross-linkable hydrogen-bonded polyelectrolyte multilayers.

Polyelectrolyte multilayers of poly(acrylic acid) (PAA) and polyacrylamide (PAAm) were prepared via hydrogen-bonding interactions. These multilayers as assembled were stable at low pH but dissolved quickly in neutral pH water. We developed methods for stabilizing these multilayers to high pH through cross-linking by heating or UV-irradiation. Thermal treatment of the multilayers, which resulted in a partial imidization between carboxylic acid and amide groups, gave the multilayer good stability at high pH. In addition, we introduced photoreactive groups in the multilayer, which rendered the film insoluble after UV irradiation. Using these selective stabilization approaches, we have succeeded in micropatterning these films by ink-jet printing and photolithography to create subtractive patterns.

Acrylic Resins↗