Biomedical subjects

Minoru Hori

Publications and source records attributed to Minoru Hori.

5 recordsLinked to original sources

PubMed2004

Deproteinizing effects on resin-tooth bond structures.

This study investigated the effects of NaOCl on resin-tooth bonds to simulate the situations of long-term durability and caries invasion. Resin-tooth bonded specimens were produced with the use of two resin adhesives (Excite and One-Bond). Resin-tooth bonded beams (adhesive area; 0.9 mm2) were serially sectioned and the specimens were immersed in 10% NaOCl medium for 0 (control), 2, 4, and 6 h after being stored in water for 24 h. After immersion, microtensile bond tests were performed. SEM fractography was conducted to calculate each failure mode by image analysis. In addition, the adhesive interface was examined with the use of TEM. In the control specimens, enamel bond strengths had no difference between Excite (45.6 +/- 15.0) and One-Bond (56.9 +/- 12.9). On the other hand, dentin bond strengths had significant difference between Excite (80.6 +/- 21.2) and One-Bond (50.7 +/- 11.2). The bond strengths decreased with increased storage time for both systems with enamel and dentin bonds. The deteriorated mineralized dentin of beams resulted in bond-strength reduction for resin-enamel bonds. For dentin bonding, the adhesive interface was gradually dissolved from the outer to the center portion of the beam. The depletion of collagen fibrils within the demineralized dentin or hybrid layer deformation was found under SEM and TEM examinations. These morphological changes are responsible for bond strength reduction of resin-dentin bonds.

Dental Materials↗

PubMed2004

In vitro testing of all-in-one adhesives as fissure sealants.

PURPOSE: To evaluate the clinical efficacy of all-in-one adhesives as fissure sealants. METHODS: Resin-enamel bonded specimens were fabricated between polished and ground enamel surfaces using two all-in-one adhesives (One-Up Bond F and Xeno CF Bond) and two resin sealants (Teethmate F-1 and Helioseal F). Specimen beams were prepared and microtensile bond tests were performed at a crosshead speed of 1 mm/minute. The bond strengths obtained were subjected to one-way ANOVA and Scheffe's F test (P < 0.05: n=12 for each group). To evaluate the etching effect of phosphoric acid and the all-in-one adhesives, the treated enamel surfaces (37% phosphoric acid, 40% phosphoric acid, or all-in-one adhesives) were examined by FE-SEM. RESULTS: The bond strengths of the two all-in-one adhesives tested to the polished enamel surface were significantly lower (P < 0.05) than to ground enamel. However, no significant differences (P > 0.05) were found between the polished and ground enamel surfaces for resin sealants using phosphoric acid. Under SEM examination, 37% or 40% phosphoric acid etched the enamel surface more than all-in-one adhesives.

Acid Etching, Dental↗

PubMed2003

Resin-enamel bonds made with self-etching primers on ground enamel.

Self-etching primer adhesives have recently been introduced to simplify bonding. However, the fundamental bonding mechanism of self-etching primers to enamel is not yet fully understood. This study aimed to investigate resin-enamel bonds of self-etching primer adhesives on ground enamel. Two self-etching primer adhesives (Clearfil Liner Bond 2 V and Clearfil SE Bond) were used in this study. A total-etch adhesive (One-Step) was used as a control. Resin-enamel beams were subjected to the microtensile bond test. Subsequently, the failure modes of all specimens were quantified using image analysis. Undemineralized and demineralized ultrathin sections of the resin-enamel bonded specimens were examined using transmission electron microscopy. The bond strengths of Clearfil SE Bond (39.8 +/- 11.9 MPa) and One-Step (46.2 +/- 12.7 MPa) were significantly greater than that of Clearfil Liner Bond 2V (30.4 +/- 6.2 MPa). Scanning electron microscopy of the fractured surfaces revealed the failure direction and weakest portion within each bond. Transmission electron microscopy showed a thin hybridized complex of resin in enamel produced by the self-etching primers without the usual micrometer-sized resin tags seen in resin-enamel bonds produced using the total-etch adhesive. The morphological features of the resin-enamel bonds produced by two self-etching primers tested were different from that created with the total-etch adhesive.

Adhesives↗

PubMed2003

Treatment planning in a case of restoration of the maxilla and mandible using osseointegrated implants with four types of bone graft.

A case is reported of a 66-year-old woman who could not use a conventional, full upper denture because of a gag reflex. In the maxillary alveolar ridge, restoration was performed on a moderately atrophied, edentulous anterior area and a small defect in the right-side posterior area. In the mandibular alveolar ridge, restoration was performed on a moderate osseous defect in each molar area resulting from tooth extraction due to severe periodontal disease. Based on careful treatment planning, four types of bone graft were used with previously designed osseointegrated implants. The atrophied maxillary alveolar ridge was restored with veneer iliac bone grafts to avoid fenestration during implant placement, while alveolar process deficiency was restored using inlay and sinus bone grafts as placements for long implant fixtures. The defects in the mandibular alveolar bone were filled with corticocancellous bone chips at the implant placement sites. A combination of immediate and secondary placement of Brånemark fixtures was used. Bone-anchored bridge-type implant prostheses were fitted approximately twelve months after surgery. Three years later, there had been no failure of implant fixtures and satisfactory functional and cosmetic restoration had been maintained.

Aged↗

PubMedDate not supplied

Effects of multiple adhesive coatings on dentin bonding.

Simple changes to bonding techniques can improve resin-dentin bond strengths. This study evaluated the effect of multiple consecutive coatings of adhesive resin on dentin by measuring both microtensile bond strength and nano-leakage following exposure to ammoniacal silver nitrate. Resin-dentin bonded specimens were prepared using two total-etch adhesives (OptiBond Solo Plus/Kerr or Single Bond/3M ESPE). During bonding, resin application and air evaporation were done 1, 2, 3, 4, 6 or 8 times on acid-etched, moist dentin surfaces. Mean microtensile bond strengths were evaluated by two-way ANOVA and Fisher's PLSD test (p<0.05; n=16 for each group). Additionally, nanoleakage of silver nitrate was evaluated by transmission electron microscopy (TEM). The results indicated that bond strengths increased with each coating up to four coats. Nanoleakage decreased with each coat, becoming very small after four or more coats. This adhesive application method can be easily applied to clinical practice, thereby improving the quality of resin-dentin bonds.

Bicuspid↗