Biomedical subjects

Nathan S Mosier

Publications and source records attributed to Nathan S Mosier.

7 recordsLinked to original sources

PubMed2007

Microscopic examination of changes of plant cell structure in corn stover due to hot water pretreatment and enzymatic hydrolysis.

Particle size associated with accessible surface area has a significant impact on the saccharification of plant cell walls by cellulolytic enzymes. Small particle sizes of untreated cellulosic substrate are more readily hydrolyzed than large ones because of higher specific surface area. Pretreatment enlarges accessible and susceptible surface area leading to enhanced cellulose hydrolysis. These hypotheses were tested using ground corn stover in the size ranges of 425-710 and 53-75 microm. Ultrastructural changes in these particles were imaged after treatment with cellulolytic enzymes before and after liquid hot water pretreatment. The smaller 53-75 microm corn stover particles are 1.5x more susceptible to hydrolysis than 425-710 microm corn stover particles. This difference between the two particle size ranges is eliminated when the stover is pretreated with liquid hot water pretreatment at 190 degrees C for 15 min, at pH between 4.3 and 6.2. This pretreatment causes ultrastructural changes and formation of micron-sized pores that make the cellulose more accessible to hydrolytic enzymes.

Cellulase↗

PubMed2006

Surface-directed boundary flow in microfluidic channels.

Channel geometry combined with surface chemistry enables a stable liquid boundary flow to be attained along the surfaces of a 12 microm diameter hydrophilic glass fiber in a closed semi-elliptical channel. Surface free energies and triangular corners formed by PDMS/glass fiber or OTS/glass fiber surfaces are shown to be responsible for the experimentally observed wetting phenomena and formation of liquid boundary layers that are 20-50 microm wide and 12 microm high. Viewing this stream through a 20 microm slit results in a virtual optical window with a 5 pL liquid volume suitable for cell counting and pathogen detection. The geometry that leads to the boundary layer is a closed channel that forms triangular corners where glass fiber and the OTS coated glass slide or PDMS touch. The contact angles and surfaces direct positioning of the fluid next to the fiber. Preferential wetting of corner regions initiates the boundary flow, while the elliptical cross-section of the channel stabilizes the microfluidic flow. The Young-Laplace equation, solved using fluid dynamic simulation software, shows contact angles that exceed 105 degrees will direct the aqueous fluid to a boundary layer next to a hydrophilic fiber with a contact angle of 5 degrees. We believe this is the first time that an explanation has been offered for the case of a boundary layer formation in a closed channel directed by a triangular geometry with two hydrophobic wetting edges adjacent to a hydrophilic surface.

Dimethylpolysiloxanes↗

PubMed2006

Surface engineering of microchannel walls for protein separation and directed microfluidic flow.

The preparation of surfaces in microfluidic devices that selectively retain proteins may be difficult to implement due to the incompatibility of derivatization methods with microdevice fabrication techniques. This review describes recently reported developments in simple and rapid methods for engineering the surface chemistries of microchannels based on construction of press-fit microdevices. These devices are fabricated by placing a glass fiber on a PDMS film and pressing the film on a silicon wafer or a microscope slide that has been derivatized with octadecyltrichlorosilane (ODS). The film adheres to the slide and forms an elliptically shaped channel around the fiber. The combination of surface wettability of a hydrophilic glass microfiber and the surrounding hydrophobic microchannel surfaces directs a narrow boundary layer of liquid next to the fiber in order to bring the sample in contact with the separation media and results in selective retention of proteins. This phenomenon may be exploited to enable microscale separation applications since there are a wide variety of fibers available with different chemistries. These may be used to rapidly fabricate microchannels that serve as stationary phases for separation at a microscale. The fundamental properties of such devices are discussed.

Electrophoresis, Microchip↗

PubMed2005

Microfiber-directed boundary flow in press-fit microdevices fabricated from self-adhesive hydrophobic surfaces.

We report a rapid microfluidic device construction technique which does not employ lithography or stamping methods. Device assembly physically combines a silicon wafer, an elastomer (poly(dimethylsiloxane) (PDMS)), and microfibers to form patterns of hydrophobic channels, wells, elbows, or orifices that direct fluid flow into controlled boundary layers. Tweezers are used to place glass microfibers in a defined pattern onto an elastomeric (PDMS) hydrophobic film. The film is then manually pressed onto a hydrophobic silicon wafer, causing it to adhere to the silicon wafer and form a liquid-tight seal around the fibers. Completed in 15 min, the technique results in an operable microdevice with micrometer-scale features of nanoliter volume. Microfiber-directed boundary flow is achieved by use of the surface wetting properties of the hydrophilic glass fiber and the hydrophobicity of surrounding surfaces. The simplicity of this technique allows quick prototyping of microfluidic components, as well as complete biosensor systems, such as we describe for the detection of pathogenic bacteria.

Air↗

PubMed2005

Industrial scale-up of pH-controlled liquid hot water pretreatment of corn fiber for fuel ethanol production.

The pretreatment of cellulose in corn fiber by liquid hot water at 160 degrees C and a pH above 4.0 dissolved 50% of the fiber in 20 min. The pretreatment also enabled the subsequent complete enzymatic hydrolysis of the remaining polysaccharides to monosaccharides. The carbohydrates dissolved by the pretreatment were 80% soluble oligosaccharides and 20% monosaccharides with <1% of the carbohydrates lost to degradation products. Only a minimal amount of protein was dissolved, thus enriching the protein content of the undissolved material. Replication of laboratory results in an industrial trial at 43 gallons per minute (163 L/min) of fiber slurry with a residence time of 20 min illustrates the utility and practicality of this approach for pretreating corn fiber. The added costs owing to pretreatment, fiber, and hydrolysis are equivalent to less than 0.84 dollars/gal of ethanol produced from the fiber. Minimizing monosaccharide formation during pretreatment minimized the formation of degradation products; hence, the resulting sugars were readily fermentable to ethanol by the recombinant hexose and by pentose-fermenting Saccharomyces cerevisiae 424A(LNH-ST) and ethanologenic Escherichia coli at yields >90% of theoretical based on the starting fiber. This cooperative effort and first successful trial opens the door for examining the robustness of the pretreatment system under extended run conditions as well as pretreatment of other cellulose-containing materials using water at controlled pH.

Biotechnology↗

PubMed2004

Rapid chromatography for evaluating adsorption characteristics of cellulase binding domain mimetics.

The cost of cellulolytic enzymes is one barrier to the economic production of fermentable sugars from lignocellulosic biomass for the production of fuels and chemicals. One functional characteristic of cellulolytic enzymes that improves reaction kinetics over mineral acids is a cellulose binding domain that concentrates the catalytic domain to the substrate surface. We have identified maleic acid as an attractive catalytic domain with pK(a) and dicarboxylic acid structure properties that hydrolyze cellulose while producing minimal degradation of the glucose formed. In this study we report results of a rapid chromatographic method to assess the binding characteristics of potential cellulose binding domains for the construction of a synthetic cellulase over a wide range of temperatures (20 degrees to 120 degrees C). Aromatic, planar chemical structures appear to be key indicators of cellulose adsorption. Indole, the side-chain of the amino acid tryptophan, has been shown to reversibly adsorb to cellulose at temperatures between 30 degrees and 120 degrees C. Trypan blue, a polyaromatic, planar molecule, was shown to be irreversibly adsorbed to cotton cellulose at temperatures of <120 degrees C on the time scale of the experiments. These results confirm the importance of hydrophobic cellulose and the cellulose-binding component of cellulolytic enzymes and cellulolytic enzyme mimetics.

Biomimetics↗

PubMed2002

Characterization of acid catalytic domains for cellulose hydrolysis and glucose degradation.

Cellulolytic enzymes consist of a catalytic domain, a linking peptide, and a binding domain. The paper describes research on carboxylic acids that have potential as catalytic domains for constructing organic macromolecules for use in cellulose hydrolysis that mimic the action of enzymes. The tested domains consist of the series of mono-, di-, and tricarboxylic acids with a range of pK(a)'s. This paper systematically characterizes the acids with respect to hydrolysis of cellobiose, cellulose in biomass, and degradation of glucose and compares these kinetics data to dilute sulfuric acid. Results show that acid catalyzed hydrolysis is proportional to H+ concentration. The tested carboxylic acids did not catalyze the degradation of glucose while sulfuric acid catalyzed the degradation of glucose above that of water alone. Consequently, overall yields of glucose obtained from cellobiose and cellulose are higher for the best carboxylic acid tested, maleic acid, when compared to sulfuric acid at equivalent solution pH.

Acids↗