PubMed Health⌕ Search

Biomedical subjects

S L Lo

Publications and source records attributed to S L Lo.

At least 19 recordsLinked to original sources

Evaluation of atmospheric deposition of nitrogen to the Feitsui reservoir in Taipei.

This research studied how the air pollutants of urban areas affect a neighboring reservoir and its water quality. Through the atmospheric dispersion process, air pollutants move from the Taipei metropolitan to the Feitsui reservoir and enter the water body through dry and wet depositions. ISCST3 (Industrial Source Complex Short Term Model), an air quality model, was used to simulate dispersion, dry deposition and wet deposition of the air pollutants. Then the nitrogen loadings to the Feitsui Reservoir were evaluated. The results indicate that wet deposition places a greater burden than dry deposition does on the water body. Wet and dry deposition of NH4+ together make up a rather large proportion of the total pollution. The ranged from 21.9 to 25.2%. Those of nitrate make up a smaller proportion, ranged from 2.0 to 2.3%. If we take indirect deposition into account and calculate the NO3- and NH4+ together, the proportion is 15.9-17.6%.

Air Pollutants↗

Methods for accelerating nitrate reduction using zerovalent iron at near-neutral pH: effects of H2-reducing pretreatment and copper deposition.

Both surface treatments, H2-reducing pretreatment at 400 degrees C and the deposition of copper as a catalyst, were attempted to enhance the removal of nitrate (40 (mg N) L(-1)) using zerovalent iron in a HEPES buffered solution at a pH of between 6.5 and 7.5. After the iron surface was pretreated with hydrogen gas, the removal of the passive oxide layers that covered the iron was indicated by the decline in the oxygen fraction (energy dispersive X-ray analysis) and the overlap of the cyclic polarization curves. The reaction rate was doubled, and the lag of the early period disappeared. Then, the deposition of copper onto freshly pretreated iron promoted nitrate degradation more effectively than that onto a nonpretreated iron surface, because of the high dispersion and small size of the copper particles. An optimum of 0.25-0.5% (w/w) Cu/Fe accelerated the rate by more than six times that of the nonpretreated iron. The aged 0.5% (w/w) Cu/Fe with continual dipping in nitrate solution for 20 days completely restored its reactivity by a regeneration process with H2 reduction. Hence, these two iron surface treatments considerably promoted the removal of nitrate from near-neutral water; the reactivity of Cu/Fe was effectively recovered.

Copper↗

Treating chemical mechanical polishing (CMP) wastewater by electro-coagulation-flotation process with surfactant.

The effect of surfactants on the treatment of chemical mechanical polishing (CMP) wastewater by electro-coagulation-flotation (ECF) process was studied. Two surfactants, cetyltrimethylammonium bromide (CTAB) and sodium dodecylsulfate (SDS) were employed in this study to compare the effect of cationic (CTAB) and anodic (SDS) surfactants on ECF. The cationic surfactant can enhance the removal of the turbidity, but anodic surfactant cannot. It can be explained by the hetero-coagulation theory. Moreover, the addition of CTAB in CMP wastewater can reduce the sludge volume and the flotation/sedimentation time in ECF process. The residual turbidity and dissolved silicon dropped with the increase of charge loading. No CTAB pollution problem exists after the ECF process.

Cetrimonium↗

Effects of the molar ratio of hydroxide and fluoride to Al(III) on fluoride removal by coagulation and electrocoagulation.

The effect of the molar ratio of hydroxide and fluoride ions to Al(III) ions (gamma(OH) and gamma(F)) on coagulation and electrocoagulation (EC) was studied to solve the problem of the over addition of acid or base. The efficiency of defluoridation was approximately 100% when the sum of gamma(OH) and gamma(F) (gamma(OH+F)) was close to 3. This finding reveals that the fluoride ions and the hydroxide ions can co-precipitate with Al(III) ions and the formula of the precipitate is Al(n)F(m)(OH)(3n-m). However, when gamma(OH) was less than 2.4, the defluoridation efficiency, given that gamma(OH+F)=3, dropped as gamma(OH) fell, because the amount of aluminum polymer formed dropped. The efficiency of defluoridation of EC exceeded that of coagulation for equal gamma(OH) and gamma(OH+F), when gamma(OH+F)>3, proving the existence of an electrocondensation effect.

Journal Article↗

Removal of fluoride from semiconductor wastewater by electrocoagulation-flotation.

This work employs an anodic surfactant, sodium dodecyl sulfate (SDS), to improve the flotation performance of the electrocoagulation-flotation (ECF) process to treated fluoride containing semiconductor wastewater following calcium precipitation. The dissolved fluoride ions and CaF(2) particles in the wastewater after calcium precipitation were effectively removed in the ECF process simultaneously. The dosage of SDS required for ECF was much less than those for dispersed air flotation (DiAF) or dissolved air flotation (DAF) processes because the CaF(2) particles can be collected by hydro-fluoro-aluminum flocs in ECF. Thus, SDS only served as a frother to make the bubbles tiny and stable in the ECF defluoridation process. The interference of co-existing anions can be overcome by increasing the dosage of calcium ions and SDS. The optimum initial acidity for ECF is close to the initial fluoride concentration after calcium precipitation; the amount of SS removed dropped rapidly if the initial acidity exceeded the optimal value because the surface charge of the hydro-fluoro-aluminum particles increased. The initial acidity of the wastewater after calcium precipitation can be modified by changing the [Ca(OH)(2)]/[Ca(2+)](T) ratio and the appropriate ratio is approximately given by the acid dissociation constant of hydrofluoric acid and the initial pH of the wastewater before calcium precipitation.

Calcium↗

Raising and controlling study of dissolved oxygen concentration in closed-type aeration tank.

This study investigated the promotion and control of dissolved oxygen (DO) concentration of the closed-type aeration tank via practical experiments in the wastewater treatment system of a 5-star hotel in Taipei. As with limited and treasured space in Taiwan, before the completion of the sewer system construction in cities, to utilize the mat foundation under large buildings as the space of sewage treatment plant still has been one of the alternatives of those sewage treatments. However, aeration tanks constructed in the mat foundation of buildings have smaller effective water depth, which will cause a lower total transfer amount of DO. Controlling the total exhaust gas flow rate can increase the pressure on such closed-type aeration tanks. The DO concentration thus may increase according to Henry's Law. Furthermore, it may enable operators to adjust the DO concentration of the aeration tank more precisely and thus sustain optimal operating conditions in these treatment facilities. Practical experiments indicated that the DO concentration of aeration tank maintains an average of 3.8 mg l(-1), obtaining the optimum operating conditions. The efficiency of the biological treatment facilities in the mat foundation could be markedly improved.

Bioreactors↗

Effects of co-existing anions on fluoride removal in electrocoagulation (EC) process using aluminum electrodes.

Batch experiments with bipolar aluminum electrodes and potentiodynamic polarization tests with monopolar systems were conducted to investigate the effects of the type and concentration of co-existing anions on defluoridation in electrocoagulation (EC) process. The results demonstrate that the type of the dominant anion directs the EC defluoridation reaction. The defluoridation efficiency was almost 100% and most of the fluoride removal reaction occurred on the surface of the anode in the solution without the co-existing anions, due to the electro-condensation effect. In the solutions with co-existing anions, most of the defluoridation took place in bulk solution. The residual fluoride concentration is a function of the total mass of Al(III) liberation from anodes and the types of the functions in the solutions with and without co-existing anions are different. The existence of sulfate ions inhibits the localized corrosion of aluminum electrodes, leading to lower defluoridation efficiency because of lower current efficiency. The presence of chloride or nitrate ions prevented the inhibition of sulfate ions, and the chloride ions were more efficient. Different corrosion types occurred in different anion-containing solutions and the form of corrosion affected the kinetic over-potential. The bypass flow causes the decrease of current efficiency and the proportion of the bypass flow of current increased due to a rise of the kinetic over potential and the conductivity of the solution.

Aluminum↗

Treatment of slaughterhouse wastewater using an activated sludge/contact aeration process.

This study combines a two-phase biological treatment system of activated sludge/contact aeration process by adding biological contact filters into the rear sector of the activated sludge aeration tank of the slaughterhouse wastewater treatment plant. This system keeps the advantages of complete mixing of substrates and microorganisms and flexible operation of the activated sludge process, and increased biological phase, less sludge, process stability and good settleability of sludge of the contact aeration process. This system could avoid the defects of sludge bulking, increased sludge production and difficult operation of the activated sludge process, and system clogging and rigid operation of the contact aeration process. Because suspended microorganisms are flowing into the contact aeration system, which then degrade or suspend within the biological contact filters after being adsorbed by the fixed biological film, on which partial bio-solids will act as seeding microorganisms. Suspended microorganisms and the dropped biological film will settled in the secondary settling tank, then reflux into the activated sludge aeration tank. The partial dropped biological film will decompose in the activated sludge aeration tank to achieve the function of decreasing sludge. Large specific gravity and good settling ability of biofilm sludge will provide better effluent quality. It has been proven through a practical experiment at a slaughterhouse wastewater treatment plant in Taiwan, that the activated sludge process effluent COD value of 150-200 mg/L and SS value of 80-100 mg/L were decreased to around 40 mg/L and 22 mg/L, respectively, after changing its system to the two-phase biological treatment system of activated sludge/contact aeration process.

Abattoirs↗

The influence of artificial cutoff on a monitoring system and the water quality of the Keelung River.

The purpose of this study was to design a water quality monitoring network for the Keelung River in order to evaluate the effects of artificial cutoff across two bend channels. A steady-state water quality model was used to simulate the BOD and DO curves. The Kriging theory was applied to select the optimal locations for a water quality monitoring network. The sampling frequency was determined by the coefficients of variation of water quality and by considering the significance level and confidence interval. After calibration and verification of the water quality model, the model was applied and the simulation results indicated that the values of DO in the new channel would be higher than those of the old channel reaches. The critical point of the oxygen sag curve would shift to the mouth of river under O75 low-flow conditions, and the BOD values in the new channel would also slightly increase. The results further indicated that more monitoring stations would be needed in the downstream reaches.

China↗

Pilot study of in-situ thermal treatment for the remediation of pentachlorophenol-contaminated aquifers.

A field pilot study of a steam injection method for the treatment of pentachlorophenol (PCP)-contaminated soil and groundwater has shown potential advantages over the traditional pump-and-treatment method. Low-pressure steam was injected 10 m below the ground surface. The ground water temperature was raised to 118 degrees C over a period of 3 months. Five soil and groundwater sampling events were performed during the pilot test. Results of sample analysis showed that the PCP concentrations in deep aquifer soil decreased dramatically whereas those in shallow aquifer soil increased. It was concluded that raising the groundwater temperature caused PCP in deep aquifer soil to be desorbed, and as the hot, deep groundwater circulated upward, it brought the desorbed PCP to the shallow aquifer. By using steam injection, PCP can be desorbed from soil and moved upward to the ground surface so that it can be removed more easily through pump-and-treatment.

Cost-Benefit Analysis↗

An integrated approach in the discovery and characterization of a novel nuclear protein over-expressed in liver and pancreatic tumors.

An integrated approach in protein discovery through the use of multidisciplinary tools was reported. A novel protein, Hcc-1, was identified by analysis of the hepatocellular carcinoma (HCC)-M cell proteome. The assembled EST sequence of the 210 amino acid novel protein was subsequently confirmed by rapid amplification of cDNA ends (RACE). A total of 687 bp at the 5' untranslated region of Hcc-1 was identified. Promoter activity and several upstream open reading frames (uORFs) were demonstrated at this region. Bioinformatics prediction showed that the first 42 amino acids of the protein is a SAP domain with sequence matches to hnRNP from various vertebrate species. The Hcc-1 protein was localized to the cell nucleus while the gene was localized to chromosome 7q22.1. Hcc-1 cDNA level was increased in pancreatic adenocarcinoma. The level was also increased in well-differentiated hepatocellular carcinoma but decreases as the carcinoma progressed to a poorly differentiated stage.

5' Untranslated Regions↗

Effect of composting on characterization and leaching of copper, manganese, and zinc from swine manure.

This research was conducted to study the influence of composting on the concentrations, water solubility, and phase association of Cu, Mn, and Zn from swine (Sus domesticus) feces. Composting of separated swine manure was performed in two piles for 122 days. The metal concentrations increased rapidly during the first 49 days and leveled off thereafter. All metal concentrations increased approximately 2.7-fold in the final compost due to decomposition of organic matter. A sequential extraction protocol was used to evaluate the humification process and partition metals into water-soluble, exchangeable, organically complexed, organically bound, solid particulate, and residual fractions. Temporal changes in the water-soluble fractions of Cu, Mn, and Zn were reflected by water-soluble organic C concentrations, which rapidly increased to a maximum at Day 18 and declined thereafter. An increase in the humic acid/fulvic acid ratio in Na4P2O7 or NaOH extracts at various stages of composting represented the humification process. During composting, the major portions of Cu, Mn, and Zn were in the organically-bound, solid particulate, and organically complexed fractions, respectively. Metal distributions in different chemical fractions were generally independent of composting age and, thus, independent of respective total metal concentrations in the composts.

Animals↗

Acupuncture for frozen shoulder.

This randomised controlled trial was undertaken to evaluate the effectiveness of acupuncture as a treatment for frozen shoulder. Thirty-five patients with a diagnosis of frozen shoulder were randomly allocated to an exercise group or an exercise plus acupuncture group and treated for a period of 6 weeks. Functional mobility, power, and pain were assessed by a blinded assessor using the Constant Shoulder Assessment, at baseline, 6 weeks and 20 weeks. Analysis was based on the intention-to-treat principle. Compared with the exercise group, the exercise plus acupuncture group experienced significantly greater improvement with treatment. Improvements in scores by 39.8% (standard deviation, 27.1) and 76.4% (55.0) were seen for the exercise and the exercise plus acupuncture groups, respectively at 6 weeks (P=0.048), and were sustained at the 20-week re-assessment (40.3% [26.7] and 77.2% [54.0], respectively; P=0.025). We conclude that the combination of acupuncture with shoulder exercise may offer effective treatment for frozen shoulder.

Acupuncture Therapy↗

Extractability and fractionation of heavy metals in chemically treated sewage sludges.

Four chemically treated sludges, lime-treated (LS), lime/sodium silicate-treated (LSS), cement-treated (CS), and cement/sodium silicate-treated (CSS) were produced form the chemical treatment of aerobic digested sewage sludge cake, using lime, cement, and sodium silicate as additives. Ex tractability and fractionation of the heavy metals (Cu, Pb, Cr, and Zn) in these products and untreated sludge (S) were investigated using sequential extraction, single extraction, and 13C cross-polarization magic angle spinning nuclear magnetic resonance analysis (13C-NMR). These approaches revealed that chemical treatment of sewage sludge makes sludge Cu, Pb, and Cr more extractable. It was attributed to the irreversible dissolution of a portion of organics at very high pH during chemical treatment of sludge. The enhanced extraction of some metals having higher affinity to organics, e.g. Cu and Pb, from the chemically treated sludges was due to their complexion with the above soluble organics.

Biological Availability↗

A geometric approach to determine adsorption and desorption kinetic constants.

A geometric method based on Langmuir kinetics has been derived to determine adsorption and desorption kinetic constants. In the conventional procedure, either the adsorption kinetic constant (k(a)c) or desorption kinetic constant (k(d)c) is found from kinetic experiments and the other is calculated by their correlation with the equilibrium constant, i.e, k(d)c = Kcon/k(a)c, where Kcon has been known from equilibrium studies. The determined constants (Kcon, k(a)c, k(d)c), if based only on the conventional procedure, may not be accurate due to their mathematical dependence. Therefore, the objectives of this study are applying a geometric approach to directly determine Langmuir kinetic constants and describe adsorption behavior. In this approach, both adsorption kinetic constant (k(a)g) and desorption kinetic constant (k(d)g) are obtained only from data of kinetic experiments, and a geometric equilibrium constant (Kgeo) is calculated by Kgeo = k(a)g/k(d)g. The deviation between Kgeo and Kcon can prove the accuracy of k(a)g and k(d)g which were determined by this method. This approach was applicable to selenate, selenite and Mg2+ adsorption onto SiO2 regardless of whether the adsorbate formed inner- or outer-sphere complexes. However, this method showed some deviation between Kcon and Kgeo for Mn2+ adsorption because of the formation of surface Mn(II)-hydroxide clusters, which was inconsistent with the basic assumption of this method of monolayer adsorption.

Adsorption↗

Adsorption/desorption properties of copper ions on the surface of iron-coated sand using BET and EDAX analyses.

This study was conducted to develop a heating process for coating hydrated iron oxide on the sand surface to utilise the adsorbent properties of the coating and the filtration properties of the sand. BET and scanning electron microscope (SEM) analyses were used to investigate the surface properties of the coated layer. An energy dispersive X-ray (EDAX) technique of analysis was used for characterising metal adsorption sites on the iron-coated sand surface. The results indicated that the iron-coated sand had more micropores and higher specific surface area because of the attachment of iron oxide. Copper ions could penetrate into the micropores and mesopores of iron oxide on sand surface, and the regeneration of the iron-coated sand could be achieved by soaking with pH = 3.0 acid solution. Besides, the results of EDAX analysis showed that copper ions were chemisorbed on the surface of iron-coated sand. Results of the study developed an innovative technology for coating iron oxide on sand surface for the treatment of heavy metal in water.

Adsorption↗

Clustered genes encoding the methyltransferases of methanogenesis from monomethylamine.

Coenzyme M (CoM) is methylated during methanogenesis from monomethyamine in a reaction catalyzed by three proteins. Using monomethylamine, a 52-kDa polypeptide termed monomethylamine methyltransferase (MMAMT) methylates the corrinoid cofactor bound to a second polypeptide, monomethylamine corrinoid protein (MMCP). Methylated MMCP then serves as a substrate for MT2-A, which methylates CoM. The genes for these proteins are clustered on 6.8 kb of DNA in Methanosarcina barkeri MS. The gene encoding MMCP (mtmC) is located directly upstream of the gene encoding MMAMT (mtmB). The gene encoding MT2-A (mtbA) was found 1.1 kb upstream of mtmC, but no obvious open reading frame was found in the intergenic region between mtbA and mtmC. A single monocistronic transcript was found for mtbA that initiated 76 bp from the translational start. Separate transcripts of 2.4 and 4.7 kb were detected, both of which carried mtmCB. The larger transcript also encoded mtmP, which is homologous to the APC family of cationic amine permeases and may therefore encode a methylamine permease. A single transcriptional start site was found 447 bp upstream of the translational start of mtmC. MtmC possesses the corrinoid binding motif found in corrinoid proteins involved in dimethylsulfide- and methanol-dependent methanogenesis, as well as in methionine synthase. The open reading frame of mtmB was interrupted by a single in-frame, midframe, UAG codon which was also found in mtmB from M. barkeri NIH. A mechanism that circumvents UAG-directed termination of translation must operate during expression of mtmB in this methanogen.

Amino Acid Sequence↗

Tritium isotope effect in high-performance liquid chromatography of eicosanoids.

A significant difference in retention time between unlabeled and the corresponding multi-tritium-labeled eicosanoid has been observed in the high performance liquid chromatography (HPLC) analysis of 11 eicosanoids. Variations in retention time range from 3-7%, depending on the separation conditions as well as the number and position of the tritium substitution. Multi-tritium-labeled eicosanoids were eluted earlier than the corresponding unlabeled eicosanoid in reversed phase HPLC, whereas no isotope effect was seen with 14C- and 3H2-eicosanoids. Considerations must be given to this tritium isotope effect whenever both multi-tritium-labeled and unlabeled eicosanoids are used for HPLC cochromatography or recovery studies.

Chromatography, High Pressure Liquid↗