Biomedical subjects

Tom T Huang

Publications and source records attributed to Tom T Huang.

5 recordsLinked to original sources

PubMed2006

Surface-directed boundary flow in microfluidic channels.

Channel geometry combined with surface chemistry enables a stable liquid boundary flow to be attained along the surfaces of a 12 microm diameter hydrophilic glass fiber in a closed semi-elliptical channel. Surface free energies and triangular corners formed by PDMS/glass fiber or OTS/glass fiber surfaces are shown to be responsible for the experimentally observed wetting phenomena and formation of liquid boundary layers that are 20-50 microm wide and 12 microm high. Viewing this stream through a 20 microm slit results in a virtual optical window with a 5 pL liquid volume suitable for cell counting and pathogen detection. The geometry that leads to the boundary layer is a closed channel that forms triangular corners where glass fiber and the OTS coated glass slide or PDMS touch. The contact angles and surfaces direct positioning of the fluid next to the fiber. Preferential wetting of corner regions initiates the boundary flow, while the elliptical cross-section of the channel stabilizes the microfluidic flow. The Young-Laplace equation, solved using fluid dynamic simulation software, shows contact angles that exceed 105 degrees will direct the aqueous fluid to a boundary layer next to a hydrophilic fiber with a contact angle of 5 degrees. We believe this is the first time that an explanation has been offered for the case of a boundary layer formation in a closed channel directed by a triangular geometry with two hydrophobic wetting edges adjacent to a hydrophilic surface.

Dimethylpolysiloxanes↗

PubMed2006

Surface engineering of microchannel walls for protein separation and directed microfluidic flow.

The preparation of surfaces in microfluidic devices that selectively retain proteins may be difficult to implement due to the incompatibility of derivatization methods with microdevice fabrication techniques. This review describes recently reported developments in simple and rapid methods for engineering the surface chemistries of microchannels based on construction of press-fit microdevices. These devices are fabricated by placing a glass fiber on a PDMS film and pressing the film on a silicon wafer or a microscope slide that has been derivatized with octadecyltrichlorosilane (ODS). The film adheres to the slide and forms an elliptically shaped channel around the fiber. The combination of surface wettability of a hydrophilic glass microfiber and the surrounding hydrophobic microchannel surfaces directs a narrow boundary layer of liquid next to the fiber in order to bring the sample in contact with the separation media and results in selective retention of proteins. This phenomenon may be exploited to enable microscale separation applications since there are a wide variety of fibers available with different chemistries. These may be used to rapidly fabricate microchannels that serve as stationary phases for separation at a microscale. The fundamental properties of such devices are discussed.

Electrophoresis, Microchip↗

PubMed2005

Microfiber-directed boundary flow in press-fit microdevices fabricated from self-adhesive hydrophobic surfaces.

We report a rapid microfluidic device construction technique which does not employ lithography or stamping methods. Device assembly physically combines a silicon wafer, an elastomer (poly(dimethylsiloxane) (PDMS)), and microfibers to form patterns of hydrophobic channels, wells, elbows, or orifices that direct fluid flow into controlled boundary layers. Tweezers are used to place glass microfibers in a defined pattern onto an elastomeric (PDMS) hydrophobic film. The film is then manually pressed onto a hydrophobic silicon wafer, causing it to adhere to the silicon wafer and form a liquid-tight seal around the fibers. Completed in 15 min, the technique results in an operable microdevice with micrometer-scale features of nanoliter volume. Microfiber-directed boundary flow is achieved by use of the surface wetting properties of the hydrophilic glass fiber and the hydrophobicity of surrounding surfaces. The simplicity of this technique allows quick prototyping of microfluidic components, as well as complete biosensor systems, such as we describe for the detection of pathogenic bacteria.

Air↗

PubMed2003

Micro-assembly of functionalized particulate monolayer on C18-derivatized SiO2 surfaces.

This work describes a simple approach to immobilize functionalized colloidal microstructures onto a C(18)-coated SiO(2) substrate via specific or non-specific bio-mediated interactions. Biotinylated bovine serum albumin pre-adsorbed onto a C(18) surface was used to mediate the surface assembly of streptavidin-coated microbeads (2.8 microm), while a bare C(18) surface was used to immobilize anti-Listeria antibody-coated microbeads (2.8 microm) through hydrophobic interactions. For a C(18) surface pre-adsorbed with bovine serum albumin, hydrophobic polystyrene microbeads (0.8 microm) and positively charged dimethylamino microbeads (0.8 microm) were allowed to self-assemble onto the surface. A monolayer with high surface coverage was observed for both polystyrene and dimethylamino microbeads. The adsorption characteristics of Escherichia coli and Listeria monocytogenes on these microbead-based surfaces were studied using fluorescence microscopy. Both streptavidin microbeads pre-adsorbed with biotinylated anti-Listeria antibody and anti-Listeria antibody-coated microbeads showed specific capture of L. monocytogenes, while polystyrene and dimethylamino microbeads captured both E. coli and L. monocytogenes non-specifically. The preparation of microbead-based surfaces for the construction of microfluidic devices for separation, detection, or analysis of specific biological species is discussed.

Adsorption↗

PubMed2003

Composite surface for blocking bacterial adsorption on protein biochips.

The design and fabrication of protein biochips requires characterization of blocking agents that minimize nonspecific binding of proteins or organisms. Nonspecific adsorption of Escherichia coli, Listeria innocua, and Listeria monocytogenes is prevented by bovine serum albumin (BSA) or biotinylated BSA adsorbed on SiO(2) surfaces of a biochip that had been modified with a C(18) coating. Biotinylated BSA forms a protein-based surface that in turn binds streptavidin. Because streptavidin has multiple binding sites for biotin, it in turn anchors other biotinylated proteins, including antibodies. Hence, biotinylated BSA simultaneously serves as a blocking agent and a foundation for binding an interfacing protein, avidin or streptavidin, which in turns anchors biotinylated antibody. In our case, the antibody is C11E9, an IgG-type antibody that binds Listeria spp. Nonspecific adsorption of another bacterium, Escherichia coli, is also minimized due to the blocking action of the BSA. The blocking characteristics of BSA adsorbed on C(18)-derivatized SiO(2) surfaces for construction of a protein biochip for electronic detection of pathogenic organisms is investigated.

Adsorption↗