Biomedical subjects

W M Ingledew

Publications and source records attributed to W M Ingledew.

At least 19 recordsLinked to original sources

PubMed2005

The importance of aeration strategy in fuel alcohol fermentations contaminated with Dekkera/Brettanomyces yeasts.

Whole corn mash fermentations infected with industrially-isolated Brettanomyces yeasts were not affected even when viable Brettanomyces yeasts out-numbered Saccharomyces yeasts tenfold at the onset of fermentation. Therefore, aeration, a parameter that is pivotal to the physiology of Dekkera/Brettanomyces yeasts, was investigated in mixed culture fermentations. Results suggest that aeration strategy plays a significant role in Dekkera/Brettanomyces-mediated inhibition of fuel alcohol fermentations. Although growth of Saccharomyces cerevisiae was not impeded, mixed culture fermentations aerated at rates of > or =20 ml air l(-1) mash min(-1) showed decreased ethanol yields and an accumulation of acetic acid. The importance of aeration was examined further in combination with organic acid(s). Growth of Saccharomyces occurred more rapidly than growth of Brettanomyces yeasts in all conditions. The combination of 0.075% (w/v) acetic acid and contamination with Brettanomyces TK 1404W did not negatively impact the final ethanol yield under fermentative conditions. Aeration, however, did prove to be detrimental to final ethanol yields. With the inclusion of aeration in the control condition (no organic acid stress) and in each fermentation containing organic acid(s), the final ethanol yields were decreased. It was therefore concluded that aeration strategy is the key parameter in regards to the negative effects observed in fuel alcohol fermentations infected with Dekkera/Brettanomyces yeasts.

Acetic Acid↗

PubMed2004

Growth rates of Dekkera/Brettanomyces yeasts hinder their ability to compete with Saccharomyces cerevisiae in batch corn mash fermentations.

Growth rates determined by linear regression analysis revealed that Saccharomyces cerevisiae consistently grew more rapidly than Brettanomyces yeasts under a wide array of batch fermentative conditions, including acetic acid stress, in normal gravity (ca. 20 degrees Plato) mashes made from ground corn. Brettanomyces yeasts only grew more rapidly than S. cerevisiae when acetic acid concentrations were elevated to industrially irrelevant levels (>0.45%, w/v). Furthermore, the three Brettanomyces isolates used in this study failed to produce significant quantities of acetic acid under pure culture fermentative conditions. In fact, the small amounts of acetic acid which accumulated in pure culture fermentations of whole corn mash were below the concentration required to inhibit the growth and metabolism of S. cerevisiae. Acetic acid concentrations in pure culture Brettanomyces fermentations exceeded 0.05% (w/v) only in media containing low levels of glucose (<4%, w/v) or when aeration rates were elevated to at least 0.03 vol. air vol.-1 mash min-1. Consequently, it was concluded that Brettanomyces yeasts would not be capable of competing with S. cerevisiae in industrial batch fermentations of whole corn mash based solely on growth rates, nor would they be capable of producing inhibitory concentrations of acetic acid in such fermentations.

Acetic Acid↗

PubMed2004

Buffering capacity of whole corn mash alters concentrations of organic acids required to inhibit growth of Saccharomyces cerevisiae and ethanol production.

Growth of Saccharomyces cerevisiae and fermentative ethanol production in the presence of acetic and lactic acids was measured in whole corn mash. In this industrial medium, as compared to glucose minimal medium, the yeast had increased tolerance to organic acid stress. It was concluded that the increased buffering capacity of whole corn mash, resulting in decreased concentration of undissociated acid, was responsible for this phenomenon.

Acetic Acid↗

PubMed2003

Control of Lactobacillus contaminants in continuous fuel ethanol fermentations by constant or pulsed addition of penicillin G.

The addition of penicillin G to combat microbial contamination in continuous fuel alcohol fermentations was performed using both continuous and pulsed addition regimes. In continuous fermentations where both Saccharomyces cerevisiae and Lactobacillus paracasei were present, the mode of addition of penicillin G determined final numbers of viable L. paracasei. When the same overall average concentration of penicillin G was added in both pulsed and continuous modes, the initial viable number of L. paracasei (8.0 x 10(9) cfu ml(-1)) decreased to a greater degree (1.02 x 10(5) cfu ml(-1) L. paracasei) when penicillin G was pulsed at 6 h frequencies at an overall average concentration of 2,475 U/l than when penicillin G was added continuously at 2,475 U/l (2.77 x 10(5) cfu ml(-1) L. paracasei). Pulsed additions over longer frequencies at 2,475 U/l were not as effective in reducing viable bacteria. Viable yeasts increased during both treatment conditions by more than 2-fold. The two addition regimes also eliminated the 40% decrease in ethanol concentration caused by the intentional bacterial infection. Although there was 3 times more bacterial death with 6 h pulsed additions compared to continuous additions of penicillin G at 2,475 U/l, there was, by that point, no practical difference in either final ethanol concentration or relative ethanol recovery.

Anti-Bacterial Agents↗

PubMed2002

Influence of medium buffering capacity on inhibition of Saccharomyces cerevisiae growth by acetic and lactic acids.

Acetic acid (167 mM) and lactic acid (548 mM) completely inhibited growth of Saccharomyces cerevisiae both in minimal medium and in media which contained supplements, such as yeast extract, corn steep powder, or a mixture of amino acids. However, the yeast grew when the pH of the medium containing acetic acid or lactic acid was adjusted to 4.5, even though the medium still contained the undissociated form of either acid at a concentration of 102 mM. The results indicated that the buffer pair formed when the pH was adjusted to 4.5 stabilized the pH of the medium by sequestering protons and by lessening the negative impact of the pH drop on yeast growth, and it also decreased the difference between the extracellular and intracellular pH values (Delta(pH)), the driving force for the intracellular accumulation of acid. Increasing the undissociated acetic acid concentration at pH 4.5 to 163 mM by raising the concentration of the total acid to 267 mM did not increase inhibition. It is suggested that this may be the direct result of decreased acidification of the cytosol because of the intracellular buffering by the buffer pair formed from the acid already accumulated. At a concentration of 102 mM undissociated acetic acid, the yeast grew to higher cell density at pH 3.0 than at pH 4.5, suggesting that it is the total concentration of acetic acid (104 mM at pH 3.0 and 167 mM at pH 4.5) that determines the extent of growth inhibition, not the concentration of undissociated acid alone.

Acetic Acid↗

PubMed2001

Effects of acetic acid and lactic acid on the growth of Saccharomyces cerevisiae in a minimal medium.

Specific growth rates (mu) of two strains of Saccharomyces cerevisiae decreased exponentially (R2 > 0.9) as the concentrations of acetic acid or lactic acid were increased in minimal media at 30 degrees C. Moreover, the length of the lag phase of each growth curve (h) increased exponentially as increasing concentrations of acetic or lactic acid were added to the media. The minimum inhibitory concentration (MIC) of acetic acid for yeast growth was 0.6% w/v (100 mM) and that of lactic acid was 2.5% w/v (278 mM) for both strains of yeast. However, acetic acid at concentrations as low as 0.05-0.1% w/v and lactic acid at concentrations of 0.2-0.8% w/v begin to stress the yeasts as seen by reduced growth rates and decreased rates of glucose consumption and ethanol production as the concentration of acetic or lactic acid in the media was raised. In the presence of increasing acetic acid, all the glucose in the medium was eventually consumed even though the rates of consumption differed. However, this was not observed in the presence of increasing lactic acid where glucose consumption was extremely protracted even at a concentration of 0.6% w/v (66 mM). A response surface central composite design was used to evaluate the interaction between acetic and lactic acids on the specific growth rate of both yeast strains at 30 degrees C. The data were analysed using the General Linear Models (GLM) procedure. From the analysis, the interaction between acetic acid and lactic acid was statistically significant (P < or = 0.001), i.e., the inhibitory effect of the two acids present together in a medium is highly synergistic.

Acetic Acid↗

PubMed2001

Changes in steady state on introduction of a Lactobacillus contaminant to a continuous culture ethanol fermentation.

Lactobacillus paracasei was introduced as a contaminant into a multistage continuous culture ethanol fermentation system at ratios of 1:100, 1:1, and 70:1 with Saccharomyces cerevisiae, but failed to overtake the yeast. None of the inoculation ratios allowed L. paracasei to affect S. cerevisiae in the first fermentor in the multistage system. S. cerevisiae remained constant at approximately 3x10(7) CFU/ml regardless of the bacterial inoculation level, and even at the 70:1 inoculation ratio, glucose, ethanol, and lactic acid concentrations did not change from the steady-state concentrations seen before bacterial inoculation. However, L. paracasei decreased steadily from its initial inoculation level of approximately 2.2x10(9) CFU/ml and stabilized at 3.7x10(5) CFU/ml after 10 days of steady-state operation. Both organisms then persisted in the multistage system at an approximate L. paracasei/S. cerevisiae ratio of 1:100 which confirms that, in continuous fuel ethanol production, it would be difficult to eliminate this bacterium. Only when the pH was controlled at 6.0 in fermentor 1 (F1) were changes seen which would affect the multistage system. Ethanol concentration then decreased by 44% after 4 days of pH-controlled operation. This coincided with an increase in L. paracasei to >10(10) CFU/ml, and a 4x increase in lactic acid concentration to 20 g/l. When the clarified contents from other fermentors (F2-F5) in the multistage system were used as growth media, L. paracasei was not able to grow in batch culture. This indicated that the first fermentor in the multistage system was the only fermentor capable of supporting the growth of L. paracasei under the described conditions.

Colony Count, Microbial↗

PubMed2001

Effect of lactobacilli on yeast growth, viability and batch and semi-continuous alcoholic fermentation of corn mash.

AIMS: The aim of this study was to evaluate interactions between Saccharomyces cerevisiae and selected strains of lactobacilli regarding cell viabilities, and production of organic acids and ethanol during fermentation. METHODS AND RESULTS: Corn mashes were inoculated with yeasts and selected strains of lactobacilli, and fermented in batch or semi-continuous (cascade) mode. Ethanolic fermentation rates and viabilities of yeast were not affected by lactobacilli unless the mash was pre-cultured with lactobacilli. Then, yeast growth was inhibited and the production of ethanol was reduced by as much as 22%. CONCLUSION: Yeasts inhibited the multiplication of lactobacilli and this resulted in reduced production of acetic and lactic acids. The self-regulating nature of the cascade system allowed the yeast to recover, even when the lactobacilli had a head start, and reduced the size of the population of the contaminating Lactobacillus to a level which had an insignificant effect on fermentation rate or ethanol yield. SIGNIFICANCE AND IMPACT OF THE STUDY: Contamination during fermentation is normally taken care of by the large yeast inoculum, although yeast growth and fermentation rates could be adversely affected by the presence of high numbers of lactobacilli in incoming mash or in transfer lines.

Acetates↗

PubMed2000

Urea hydrogen peroxide reduces the numbers of lactobacilli, nourishes yeast, and leaves no residues in the ethanol fermentation.

Urea hydrogen peroxide (UHP) at a concentration of 30 to 32 mmol/liter reduced the numbers of five Lactobacillus spp. (Lactobacillus plantarum, L. paracasei, Lactobacillus sp. strain 3, L. rhamnosus, and L. fermentum) from approximately 10(7) to approximately 10(2) CFU/ml in a 2-h preincubation at 30 degrees C of normal-gravity wheat mash at approximately 21 g of dissolved solids per ml containing normal levels of suspended grain particles. Fermentation was completed 36 h after inoculation of Saccharomyces cerevisiae in the presence of UHP, even when wheat mash was deliberately contaminated (infected) with L. paracasei at approximately 10(7) CFU/ml. There were no significant differences in the maximum ethanol produced between treatments when urea hydrogen peroxide was used to kill the bacteria and controls (in which no bacteria were added). However, the presence of L. paracasei at approximately 10(7) CFU/ml without added agent resulted in a 5.84% reduction in the maximum ethanol produced compared to the control. The bactericidal activity of UHP is greatly affected by the presence of particulate matter. In fact, only 2 mmol of urea hydrogen peroxide per liter was required for disinfection when mashes had little or no particulate matter present. No significant differences were observed in the decomposition of hydrogen peroxide in normal-gravity wheat mash at 30 degrees C whether the bactericidal agent was added as H(2)O(2) or as urea hydrogen peroxide. NADH peroxidase activity (involved in degrading H(2)O(2)) increased significantly (P = 0.05) in the presence of 0.75 mM hydrogen peroxide (sublethal level) in all five strains of lactobacilli tested but did not persist in cells regrown in the absence of H(2)O(2). H(2)O(2)-resistant mutants were not expected or found when lethal levels of H(2)O(2) or UHP were used. Contaminating lactobacilli can be effectively managed by UHP, a compound which when used at ca. 30 mmol/liter happens to provide near-optimum levels of assimilable nitrogen and oxygen that aid in vigorous fermentation performance by yeast.

Carbamide Peroxide↗

PubMed1999

Bacterial surface antigen-specific monoclonal antibodies used to detect beer spoilage pediococci.

Fourteen monoclonal antibodies (Mabs) were isolated that react with surface antigens of Pediococcus beer spoilage organisms, including P. damnosus, P. pentosaceous, P. acidilactici, and unspeciated isolates. Immunoblotting, enzyme immunoassays (EIAs) of protease- and neuraminidase-treated surface antigen extracts, carbohydrate competition EIAs, and cardiolipin EIAs were used to characterize the bacterial antigens involved in Mab binding. Antigen stability in situ was tested by protease treatment or surface antigen extraction of washed bacteria. In most cases, the Mabs bind to Pediococcus surface antigens that appear to be covalently bound cell wall polymers resistant to alteration or removal from the bacterial surface. These bacterial surface antigen reactive Mabs show good potential for rapid, sensitive, and specific immunoassay detection of Pediococcus beer spoilage organisms.

Animals↗

PubMed1999

Epitope mapping of monoclonal antibodies specific for the directly cross-linked mesodiaminopimelic acid peptidoglycan found in the anaerobic beer spoilage bacterium Pectinatus cerevisiiphilus.

Nineteen monoclonal antibodies (Mabs) were isolated based on reactivity with disrupted Pectinatus cerevisiiphilus cells. All of the Mabs reacted with cells from which the outer membrane had been stripped by incubation with sodium dodecyl sulphate, suggesting the peptidoglycan (PG) layer was involved in binding. Mab reactivity with purified PG confirmed this. Epitope mapping revealed the Mabs in total recognize four binding sites on the PG. Mabs specific for each of the four sites also bound strongly to disrupted Pectinatus frisingensis, Selenomonas lacticifix, Zymophilus paucivorans, and Zymophilus raffinosivorans cells, but weakly to disrupted Megasphaera cerevisiae cells. No antibody reactivity was seen with disrupted cells of 11 other species of Gram-negative bacteria. These results confirm that a common PG structure is used by several species of anaerobic Gram-negative beer spoilage bacteria. These results also indicate that PG-specific Mabs can be used to rapidly detect a range of anaerobic Gram-negative beer spoilage bacteria, provided the bacterial outer membrane is first removed to allow antibody binding.

Animals↗

PubMed1999

Brewing spoilage Lactobacilli detected using monoclonal antibodies to bacterial surface antigens.

A panel of thirteen monoclonal antibodies (Mabs) was assembled that reacts with surface antigens on eight of eleven Lactobacillus brewing spoilage organisms, including one or more of L. brevis, L. buchneri, L. casei-alactosus, L. plantarum, or unspeciated isolate(s). Immunoblotting was done to identify the antigens involved in Mab binding. Antigen stability in situ was tested by protease treatment and by surface antigen extraction of washed bacteria. Protease susceptibility of extracted surface antigens was also examined. In most cases, Lactobacillus surface antigens detected by the Mabs appear to be noncovalently bound proteins readily altered or removed from the bacterium by various environmental conditions. This research identifies brewing conditions that need to be tested to ascertain whether bacterial surface antigen-reactive Mabs can be used for the rapid, sensitive, and specific detection of Lactobacillus brewing spoilage organisms.

Animals↗

PubMed1997

Use of virginiamycin to control the growth of lactic acid bacteria during alcohol fermentation.

The antibiotic virginiamycin was investigated for its effects on growth and lactic acid production by seven strains of lactobacilli during the alcoholic fermentation of wheat mash by yeast. The lowest concentration of virginiamycin tested (0.5 mg Lactrol kg-1 mash), was effective against most of the lactic acid bacteria under study, but Lactobacillus plantarum was not significantly inhibited at this concentration. The use of virginiamycin prevented or reduced potential yield losses of up to 11% of the produced ethanol due to the growth and metabolism of lactobacilli. However, when the same concentration of virginiamycin was added to mash not inoculated with yeast, Lactobacillus rhamnosus and L. paracasei grew after an extensive lag of 48 h and L. plantarum grew after a similar lag even in the presence of 2 mg virginiamycin kg-1 mash. Results showed a variation in sensitivity to virginiamycin between the different strains tested and also a possible reduction in effectiveness of virginiamycin over prolonged incubation in wheat mash, especially in the absence of yeast.

Anti-Bacterial Agents↗

PubMed1997

Effects of lactobacilli on yeast-catalyzed ethanol fermentations.

Normal-gravity (22 to 24 degrees Plato) wheat mashes were inoculated with five industrially important strains of lactobacilli at approximately 10(5), approximately 10(6), approximately 10(7), approximately 10(8), and approximately 10(9) CFU/ml in order to study the effects of the lactobacilli on yeast growth and ethanol productivity. Lactobacillus plantarum, Lactobacillus paracasei, Lactobacillus #3, Lactobacillus rhamnosus, and Lactobacillus fermentum were used. Controls with yeast cells but no bacterial inoculation and additional treatments with bacteria alone inoculated at approximately 10(7) CFU/ml of mash were included. Decreased ethanol yields were due to the diversion of carbohydrates for bacterial growth and the production of lactic acid. As higher numbers of the bacteria were produced (depending on the strain), 1 to 1.5% (wt/vol) lactic acid resulted in the case of homofermentative organisms. L. fermentum, a heterofermentative organism, produced only 0.5% (wt/vol) lactic acid. When L. plantarum, L. rhamnosus, and L. fermentum were inoculated at approximately 10(6) CFU/ml, an approximately 2% decrease in the final ethanol concentration was observed. Smaller initial numbers (only 10(5) CFU/ml) of L. paracasei or Lactobacillus #3 were sufficient to cause more than 2% decreases in the final ethanol concentrations measured compared to the control. Such effects after an inoculation of only 10(5) CFU/ml may have been due to the higher tolerance to ethanol of the latter two bacteria, to the more rapid adaptation (shorter lag phase) of these two industrial organisms to fermentation conditions, and/or to their more rapid growth and metabolism. When up to 10(9) CFU of bacteria/ml was present in mash, approximately 3.8 to 7.6% reductions in ethanol concentration occurred depending on the strain. Production of lactic acid and a suspected competition with yeast cells for essential growth factors in the fermenting medium were the major reasons for reductions in yeast growth and final ethanol yield when lactic acid bacteria were present.

Ethanol↗

PubMed1994

Fuel alcohol production: optimization of temperature for efficient very-high-gravity fermentation.

The time required to end ferment wheat mash decreased as the temperature was increased from 17 to 33 degrees C, but it increased as the concentration of dissolved solids was raised from 14.0 to 36.5 g/100 ml. Ethanol yield was not appreciably affected. Over the range of fermentation temperatures tested, the addition of urea accelerated the rate of fermentation, decreased the time required to complete fermentation at all dissolved-solid concentrations, and stimulated the production of slightly more ethanol than was produced by the corresponding unsupplemented control mashes. The optimum temperature for maximum ethanol production in urea-supplemented very-high-gravity wheat mash was 27 degrees C. These data are important for the industrial assessment of very-high-gravity fermentation technology.

Journal Article↗

PubMed1994

Effects of particulate materials and osmoprotectants on very-high-gravity ethanolic fermentation by Saccharomyces cerevisiae.

The effects of osmoprotectants (such as glycine betaine and proline) and particulate materials on the fermentation of very high concentrations of glucose by the brewing strain Saccharomyces cerevisiae (uvarum) NCYC 1324 were studied. The yeast growing at 20 degrees C consumed only 15 g of the sugar per 100 ml from a minimal medium which initially contained 35% (wt/vol) glucose. Supplementing the medium with a mixture of glycine betaine, glycine, and proline increased the amount of sugar fermented to 30.5 g/100 ml. With such supplementation, the viability of the yeast cells was maintained above 80% throughout the fermentation, while it dropped to less than 12% in the unsupplemented controls. Among single additives, glycine was more effective than proline or glycine betaine. On incubating the cultures for 10 days, the viability decreased to only 55% with glycine, while it dropped to 36 and 27%, respectively, with glycine betaine and proline. It is suggested that glycine and proline, known to be poor nitrogen sources for growth, may serve directly or indirectly as osmoprotectants. Nutrients such as tryptone, yeast extract, and a mixture of purine and pyrimidine bases increased the sugar uptake and ethanol production but did not allow the population to maintain the high level of cell viability. While only 43% of the sugar was fermented in unsupplemented medium, the presence of particulate materials such as wheat bran, wheat mash insolubles, alumina, and soy flour increased sugar utilization to 68, 75, 81, and 82%, respectively.

Betaine↗

PubMed1992

Detection of Pediococcus spp. in brewing yeast by a rapid immunoassay.

A membrane immunofluorescent-antibody test was developed to detect diacetyl-producing Pediococcus contaminants in brewery pitching yeast (yeast [Saccharomyces cerevisiae] slurry collected for reinoculation). Centrifugations at 11 and 5,100 x g separate yeast cells from bacteria and concentrate the bacteria, respectively. Pelleted bacteria resuspended and trapped on a black membrane filter are reacted with monoclonal antibodies specific for cell surface antigens and then with fluorescein-conjugated indicator antibodies. Whether pitching yeast is contaminated with pediococci at 0.001% is determined in less than 4 h. The sensitivity of the assay is 2 orders of magnitude below the Pediococcus detection limit of direct microscopy.

Fluorescent Antibody Technique↗

PubMed1992

Relationship of low lysine and high arginine concentrations to efficient ethanolic fermentation of wheat mash.

Very high gravity wheat mashes containing 20 or more grams of carbohydrates per 100 mL were fermented completely by Saccharomyces cerevisiae, even though these mashes contained low amounts of assimilable nitrogen. Supplementation of wheat mashes with various amino acids or with yeast extract, urea, or ammonium sulfate reduced the fermentation time. However, lysine or glycine added as single supplements, inhibited yeast growth and fermentation. With lysine, yeast growth was severely inhibited, and a loss of cell viability as high as 80% was seen. Partial or complete reversal of lysine-induced inhibition was achieved by the addition of a number of nitrogen sources. All nitrogen sources that relieved lysine-induced inhibition of yeast growth also promoted uptake of lysine and restored cell viability to the level observed in the control. They also increased the rate of fermentation. Experiments with minimal media showed that for lysine to be inhibitory to yeast growth, assimilable nitrogen in the medium must be in growth-limiting concentrations or totally absent. In the presence of excess nitrogen, lysine stimulated yeast growth and fermentation. Results indicate that supplementing wheat mash with other nitrogen sources increases the rate of fermentation not only by providing extra nitrogen but also by reducing or eliminating the inhibitory effect of lysine on yeast growth.

Arginine↗