Contoured elastic-membrane microvalves for microfluidic network integration.

A M Young; T M Bloomstein; S T Palmacci

doi:10.1115/1.2798039

Home/Archive/PubMed

PubMed · 10080082

Contoured elastic-membrane microvalves for microfluidic network integration.

A M Young·T M Bloomstein·S T Palmacci

View original source ↗Export metadata ↓

Abstract

A contoured elastic-membrane microvalve is presented that enables integrated microfluidic processing at the network level. This method takes advantage of two ideas to improve performance: flexible elastic membranes (which enable high-performance shutoff and reduced footprint), and three-dimensionally contoured valve geometries (which reduce dead volume, improve fluidic priming, and reduce susceptibility to cavitation at high fluid velocities). We describe the use of laser-induced etching for microfluidic manifold fabrication, discuss the nonlinear load-deflection behavior of elastic membranes that can occur below 30 psi, and present flow-rate data for microvalves under inlet pressures of 0-20 psi with zero applied membrane pressure. Valve-closure data for inlet pressures of 0-30 psi are presented for fully assembled microvalve structures. The microvalve structures under test were capable of turning off flows of > 20 microL/s. These flow rates were shown to be limited by inlet and outlet flow resistances and not by the valve structure itself, so that higher maximum flow rate capabilities should be readily achieved.

Explore related subjects

Computer-Aided Design Elasticity Equipment Design Materials Testing Membranes, Artificial Models, Cardiovascular Nonlinear Dynamics Pressure Rheology Silicones Stress, Mechanical Journal Article Research Support, Non-U.S. Gov't

Keep this discovery

Explore connections, maps & timelines

BibTeX RIS

A M Young, T M Bloomstein, S T Palmacci. 1999. Contoured elastic-membrane microvalves for microfluidic network integration.. https://doi.org/10.1115/1.2798039

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related citations

PubMed2004

Optical modeling of extraoral defects.

In order to reduce the stress caused to patients by conventional methods of modeling using computed tomography (CT) or magnetic resonance imaging (MRI), an optical modeling process has been developed for extraoral defects and body areas. The selected body part is digitized using optical 3-coordinate measuring technology, providing an extensive data record. This is adapted for further use by equalizing the point clouds to obtain a Computer Aided Design (CAD) model, which is converted to a physical model by means of a stereolithographic process. With this technology, the patient's physical and psychological stress may be reduced. This article describes a technique for optical modeling of an ocular prosthesis.

Computer-Aided Design↗

PubMed2003

Development of a novel aspherical mirror bender for an active grating.

A novel monolithic mechanical bender has been designed and fabricated to meet the requirements of an active polynomial grating in a new soft X-ray scattering and emission beamline at the National Synchrotron Radiation Research Center, Taiwan. This compact bender achieves nearly fixed center point under different bending conditions. Moreover, the compact bender can be bent to a desirable third-order polynomial surface profile to cancel the defocus and coma aberrations using two PZT actuators. Theoretical analysis reveals that the grating has unprecedented spectral resolving power. A detailed mechanical analysis has been conducted and a prototype bender was fabricated and tested. The results indicate that the performance of the bender is excellent and is therefore suitable to be used in the active grating.

Computer-Aided Design↗

PubMed2003

Cyclen substitution with urea-containing dendrimeric branches. Theoretical study considering the concept of collectivity.

Equilibrium structures of novel dendrimeric compounds consisting of 1,4,7,10-tetraazacyclododecane (cyclen) mono- to tetra-substituted with four different dendrimeric branches have been studied. It has been shown using molecular dynamics (MD) that, even in the presence of the macrocycle cyclen, the most stable conformations are those with a globular shape due to close contact interactions between poly-functional branches. No collapse of cyclen occurred, making this cavity available for metal complexation. Terminal branches A=NHCOOtBu, B=OSi(Me)2tBu, C=Imidazole and D=CN have different molecular volumes in the decreasing order: B>A>C>D. This conclusion is in accord with the long range interaction energies, showing that the larger the volume the less the steric hindrance. Considering these energy values, the stability of the systems follows exactly the same tendency as observed for the molecular volume. More polar groups like A=NHCOOtBu and D=CN impart extra stability due to long range interactions between atoms separated by exactly three chemical bonds. The negative charge inside the cyclen cavity increases with the volume of the branches. Besides cyclen, urea groups located at the middle of the branches represent another independent point of negative charge for eventual interaction with small molecules. These compounds show a sum of small contributions of the functionalities in a collective fashion.

Computer-Aided Design↗