PubMed Health⌕ Search

PubMed · 11539134

Lunar soil evolution processes and Apollo 16 core 60013/60014.

Abstract

Soils of the 62-cm deep Apollo 16 double drive tube 60013/14 are mature at the top and submature at the bottom. Modal analyses of 5529 grains from the 90-150 micrometers and the 500-1000 micrometers fractions from 12 levels of the core show that, in general, agglutinate abundance increases somewhat monotonically to the top and mimics the Is/FeO profile. There is a general decrease in the modal abundance of monomineralic fragments towards the top, suggesting that agglutinates were formed in part at the expense of monomineralic grains, especially feldspars, which are by far the most abundant mineral in these soils. In detail, the top 27 cm of the core differs from the bottom 21 cm, and the middle 14 cm is intermediate in its properties. In the upper segment, variations in the abundances of feldspars correspond with those of feldspathic fragmental breccias and cataclastic anorthosites; in the bottom segment, a similar but weak correspondence between feldspars and crystalline matrix breccias is observed. Mixing of the comminuted products of these three rock types likely produced the bulk of the core material. Many single feldspars in all size fractions are remarkably fresh, show no damage from shock, and are similar in appearance to the large feldspars in anorthosites and feldspathic fragmental breccias, which we consider to be the primary sources of single feldspars in this core. Major (Na, Al, Si, K, Ca) and minor (Fe, Ba) element analyses of 198 single feldspar grains indicate the presence of only one population of feldspars, which is consistent with our interpretation of feldspar provenance. Classification of 890 monomineralic feldspar, olivine, pyroxene, and glass spherules on the basis of the presence or absence of thin brownish coating--related to reworking at the surface--shows that coated grains are much more abundant in the top segment than in the bottom segment. A comparison with the mixing and maturation model (McKay et al., 1977) of soils in the core 60009/10, some 60 m away from 60013/14, shows that mixtures of an immature, nearly pure plagioclase soil (dominant in 60009/10) and another immature, crystalline breccia-rich soil (dominant in 60013/14) may have matured through in situ reworking to produce the soils under investigation. We conclude that the soils in this core are products of mixing along soil evolution Path 2 of McKay et al. (1974). Superimposed on that soil column is the reworking of the upper part, which has evolved more recently along Path 1. This core thus represents a consanguineous column of the lunar regolith with an upper reworked segment.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

A Basu, D S McKay. 1995. Lunar soil evolution processes and Apollo 16 core 60013/60014.. https://doi.org/10.1111/j.1945-5100.1995.tb01111.x

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related citations

Concentrations of polychlorinated dibenzo-p-dioxins in processed ball clay from the United States.

Processed ball clays commonly used by the ceramic art industry in the United States were collected from retail suppliers and analyzed for the presence and concentration of the 2,3,7,8-Cl substituted polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDDs/PCDFs). The average PCDD toxic equivalent (TEQ) concentrations of these processed ball clays was approximately 800 pg/g (TEQ-WHO) with characteristic congener profiles and isomer distributions similar to patterns of previously analyzed raw and processed ball clays. The PCDF concentrations were below the average limit of detection (LOD) of 0.5 pg/g. Correlation analyses reveal no significant relationship between total organic carbon (TOC) and either individual, homologues, and total tetra-through octa-chlorinated PCDD congeners, or TEQ concentrations of the processed ball clays. The results are consistent with earlier studies on levels of PCDDs in ball clays. Data from earlier studies indicated that dioxins may be released to the environment during the processing of raw clay or the firing process used in commercial ceramic facilities. The presence of dioxin in the clays also raises concerns about potential occupational exposure for individuals involved in the mining/processing of ball clay, ceramics manufacturing and ceramic artwork.

Aluminum Silicates↗

Dynamics of interactions involving deformable drops: hydrodynamic dimpling under attractive and repulsive electrical double layer interactions.

A model developed previously to analyze force measurements between two deformable droplets in the atomic force microscope [Langmuir 2005, 21, 2912-2922] is used to model the drainage of an aqueous film between a mica plate and a deformable mercury drop for both repulsive and attractive electrical double-layer interactions between the mica and the mercury. The predictions of the model are compared with previously published data [Faraday Discuss. 2003, 123, 193-206] on the evolution of the aqueous film whose thickness has been measured with subnanometer precision. Excellent agreement is found between theoretical results and experimental data. This supports the assumptions made in the model which include no-slip boundary conditions at both interfaces. Furthermore, the successful fit attests to the utility of the model as a tool to explore details of the drainage mechanisms of nanometer-thick films in which fluid flow, surface deformations, and colloidal forces are all involved. One interesting result is that the model can predict the time at which the aqueous film collapses when attractive mica-mercury forces are present without the need to invoke capillary waves or other local instabilities of the mercury/electrolyte interface.

Aluminum Silicates↗

Biological evaluation of an apatite-mullite glass-ceramic produced via selective laser sintering.

The biological performance of a porous apatite-mullite glass-ceramic, manufactured via a selective laser sintering (SLS) method, was evaluated to determine its potential as a bone replacement material. Direct contact and extract assays were used to assess the cytotoxicity of the material. A pilot animal study, implanting the material into rabbit tibiae for 4 weeks, was also carried out to assess in vivo bioactivity. The material produced by SLS did not show any acute cytotoxic effects by either contact or extract methods. There was no evidence of an apatite layer forming on the surface of the material when soaked in SBF for 30 days, suggesting that the material was unlikely to exhibit bioactive behaviour in vivo. It is hypothesized that the material was unable to form an apatite layer in SBF due to the fact that this glass-ceramic was highly crystalline and the fluorapatite crystal phase was relatively stable in SBF, as were the two aluminosilicate crystal phases. There was thus no release of calcium and phosphorus and no formation of silanol groups to trigger apatite deposition from solution within the test time period. Following implantation in rabbit tibiae for 4 weeks, bone was seen to have grown into the porous structure of the laser-sintered parts, and appeared to be very close to, or directly contacting, the material surface. This result may reflect the local environment in vivo compared to that artificially found with the in vitro SBF test and, furthermore, confirms previous in vivo data on these glass-ceramics.

Aluminum Silicates↗