PubMed · 11799700
The source did not provide an abstract. Follow the original record for more information.
Explore connections, maps & timelines
M Bagby. 2001. The Bagby Modification.. https://pubmed.ncbi.nlm.nih.gov/11799700/
Cite the original work for its findings. Save a collection to share your selection of sources.
KEEP EXPLORING
The aim of this study was to evaluate the influence of techniques of composite resin polymerization and insertion on microleakage and microhardness. One hundred and eighty class II cavities were prepared in bovine teeth and assigned to six groups: G1 - bulk filling + conventional polymerization; G2 - bucco-lingual increments + conventional polymerization; G3 - bulk filling + soft-start polymerization; G4 - bucco-lingual increments + soft-start polymerization; G5 - bulk filling + progressive polymerization; G6 - bucco-lingual increments + progressive polymerization. All cavities were restored with the Z100/Single Bond system (3M). After thermocycling, the samples were immersed in 2% methylene blue dye solution for 4 hours. Half of the samples were embedded in polystyrene resin, and Knoop microhardness was measured. The Kruskal-Wallis test did not reveal statistical differences (p > 0.05) between the polymerization and insertion techniques as to microleakage. Regarding microhardness, the two-way ANOVA and the Tukey test did not reveal statistical differences between the restorative techniques (p > 0.05), but progressive polymerization (G5 and G6) was associated with smaller Knoop microhardness values (p < 0.05): G = 144.11; G2 = 143.89; G3 = 141.14; G4 = 142.79; G5 = 132.15; G6 = 131.67. It was concluded that the evaluated polymerization and insertion techniques did not affect marginal microleakage, but a decrease in microhardness occurred when progressive polymerization was carried out.
Hydrogels of carbomer (C) loaded with model slightly soluble fluoroquinolone antimicrobials (AMFQ), norfloxacin (I) and ciprofloxacin (II) were prepared to evaluate their physical and delivery properties. Thus, dispersions of 0.25% of C loaded with 0.2-0.5 mol equivalents of AMFQ and 0.2-0.5 mol equivalents of NaOH yielded pseudoplastic hydrogels with a high negative electrokinetic potential and good physical stability. Concentration of AMFQ in the hydrogels was, respectively, 7.2 and 34 times higher than I and II aqueous solubility, indicating a high increase in aqueous compatibility. Release of AMFQ in bicompartimetal Franz type cell occurred by zero order kinetics. Delivery rate constant (k(0)) was five to six times higher as water was replaced by NaCl solution as receptor medium. Release in agar dishes revealed that, even under high dilution, delivery remains modulated. Intestinal absorption flux coefficient in everted rat intestine (k(U)) were measured with reference solutions (RS) of free AMFQ (k(U)(RS) II>k(U)(RS) I) and with hydrogels (H), in which the pattern was reversed since k(U)(H) I>k(U)(H) II. As expected k(U)(H) II was 0.55 times lower than k(U)(RS) II. However, k(U)(H) I was 1.37 times higher than its reference, which cannot be explained from the analysis of k(0) and k(U)(RS) alone. Hydrogels C-AMFQ behave as a reservoir of AMFQ able to deliver it at a constant rate and would be useful to design topical and or systemic dosage forms.
Eudragit RS and RL are biocompatible non-swelling polymers that widely used in the preparation of sustained release drug delivery systems. In this study, the effect of thermal treating on the tensile strength of tablets and release of indomethacin from Eudragit RS and RL matrices were investigated. The results showed that thermal treating at 40 degrees C has no effect on the release of the drug, whereas heat-treating at temperatures higher than 50 or 60 degrees C decreases the release rate of indomethacin from Eudragit RS or RL, respectively. It was shown that the duration of the heat treatment was also an important factor in controlling the release rate of indomethacin from Eudragit matrices. The results showed that an increase in the duration of the heat treatment from 2 to 24 h resulted in a reduction in the release rate of the drug. The heating of the matrices over 24 h had no significant effect on the release rate of indomethacin. It was shown that heat treatment of the matrices over the glass transition temperature of the polymer can prolong the drug release but had no significant effect on the tensile strength of tablets.