PubMed Health⌕ Search

PubMed · 15984929

Desferrioxamine release from gelatin-based systems.

Abstract

The conventional treatment with regular red-blood-cell transfusions and simultaneous chelation of excess iron with DFO (desferrioxamine) improves quality of life of thalassaemic patients while increasing their rate of survival considerably. Although DFO is the main iron- chelating drug currently utilized, it has various drawbacks, including high cost, poor oral effectiveness, toxicity and short plasma half-life. It has to be administered by slow, subcutaneous infusion during blood transfusion for 8-12 h at night, 5-7 nights a week, and this leads to a very poor patient compliance. In order to avoid frequent and uncomfortable infusions of DFO, application of controlled-release systems might be alternative routes in the supportive treatment of thalassaemia. In the present study, GMs (gelatin microspheres) and GFs (gelatin films) were prepared by coacervation and casting methods respectively to develop controlled DFO-release systems. Cross-linking by glutaraldehyde and carbodi-imide were performed to increase the stability of gelatin matrices. Microspheres and films prepared without the addition of cross-linker degraded completely in 4 h. On the other hand, addition of cross-linker extended this time from hours to weeks depending on the added amount. Therefore the amount of DFO released from microspheres in 7 days was found to be in the range 12-82%, whereas the amount permeated through the films in 5.0 h was found to be in the range 34-67%. GFs were elastic and demonstrated good mechanical properties. Films achieved 0.14-0.69 MPa tensile strength, with 0.12-1.29 MPa elastic modulus and 26.49-109.38% strain values at break point. These studies showed that gelatin-based controlled-release systems could be improved and could be good candidates for the production of long-term DFO-carrying systems.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Kezban Ulubayram, Aysel Kiziltay, Elvan Yilmaz, Nesrin Hasirci. 2005. Desferrioxamine release from gelatin-based systems.. https://doi.org/10.1042/ba20050084

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related citations

Development of a 3D cell culture system for investigating cell interactions with electrospun fibers.

There are many variables to be considered in studying how cells interact with 3D scaffolds used in tissue engineering. In this study we investigated the influence of the fiber diameter and interfiber spaces of 3D electrospun fiber scaffolds on the behavior of human dermal fibroblasts. Fibers of two dissimilar model materials, polystyrene and poly-L-lactic acid, with a broad range of diameters were constructed in a specifically developed 3D cell culture system. When fibroblasts were introduced to freestanding fibers, and encouraged to "walk the plank," a minimum fiber diameter of 10 microm was observed for cell adhesion and migration, irrespective of fiber material chemistry. A distance between fibers of up to 200 microm was also observed to be the maximum gap that could be bridged by cell aggregates--a behavior not seen in conventional 2D culture. This approach has identified some basic micro-architectural parameters for electrospun scaffold design and some key differences in fibroblast growth in 3D. We suggest the findings will be of value for optimizing the integration of cells in these scaffolds for skin tissue engineering.

Biocompatible Materials↗

Improved catalytic properties of immobilized lipases by the presence of very low concentrations of detergents in the reaction medium.

The addition of a very small concentration of a detergent (in many instances under the critical micellar concentration (cmc)) has been found to greatly increase the activity of immobilized lipases, using those from Pseudomonas fluorescens (PFL) and Candida antarctica (isoform B) as model enzymes. However, the detergents may also have a negative effect on enzyme activity; in fact, for all enzyme preparations and substrates the activity/detergent concentration curve reached a maximum value and started to decrease, in many instances even under the initial value. The concentration and nature of the detergent (SDS, CTAB, Triton X-100, or X-45) that permitted the maximum hyperactivation was different depending on the substrate. The best hyperactivation values promoted by the presence of detergent were over a 20-fold factor. The presence of detergents permitted the inhibition of lipases by irreversible covalent inhibitors (e.g., 4-(2-aminoethyl)benzenesulfonyl fluoride hydrochloride) (AEBSF) while the enzyme, in the absence of detergent, is not inhibited by these irreversible inhibitors. This suggested that the main effect of the detergents is to shift the conformational equilibrium of lipases toward the open form. Moreover, the presence of detergents also permitted to improve the enantioselectivity exhibited by the immobilized lipases in some cases. For example, the enantioselectivity of PFL-glyoxyl agarose increased from 40 to more than 100 in the hydrolysis of (+/-)-2-hydroxy-4-phenylbutyric acid ethyl ester by using 0.1% CTAB.

Biocompatible Materials↗

Development of wollastonite-poly(ethylmethacrylate co-vinylpyrrolidone) based materials for multifunctional devices.

The manufacturing of a composite made of a synthetic bioactive ceramic, pseudowollastonite (psW), and a bioresorbable copolymer ethylmethacrylate-vinylpyrrolidone (EMA/VP) is presented in this article. psW porous blocks were produced by dipping an open porous polyurethane foam in a psW containing slurry. A 40/60 wt % EMA/VP monomers mixture was poured on the blocks, and free radical polymerization initiated by azobis(isobutyronitrile) at 50 degrees C. Disks of 1 mm height were obtained by cutting the composite with a diamond saw, and bioresorption and bioactivity of the specimens were tested by immersion of the disks into SBF. A ceramic/polymer weight ratio of 72/28, greater than the usually achievable ratio by polymeric solidification of slurries of monomers charged with a powdered solid component, has been obtained. The system is bioactive and does not change the pH of the medium during the degradation test.

Biocompatible Materials↗