PubMed Health⌕ Search

PubMed · 2331471

Preferential interactions determine protein solubility in three-component solutions: the MgCl2 system.

Abstract

The correlation between protein solubility and the preferential interactions of proteins with solvent components was critically examined with aqueous MgCl2 as the solvent system. Preferential interaction and solubility measurements with three proteins, beta-lactoglobulin, bovine serum albumin, and lysozyme, resulted in similar patterns of interaction. At acid pH (pH 2-3) and lower salt concentrations (less than 2 M), the proteins were preferentially hydrated, while at higher salt concentrations, the interaction was either that of preferential salt binding or low salt exclusion. At pH 4.5-5, all three proteins exhibited either very low preferential hydration or preferential binding of MgCl2. These results were analyzed in terms of the balance between salt binding and salt exclusion attributed to the increase in the surface tension of water by salts, which is invariant with conditions. It was shown that the increase in salt binding at high salt concentration is a reflection of mass action, while its decrease at acid pH is due to the electrostatic repulsion between Mg2+ ions and the high net positive charge on the protein. The preferential interaction pattern was paralleled by the variation of protein solubility with solvent conditions. Calculation of the transfer free energies from water to the salt solutions for proteins in solution and in the precipitate showed dependencies on salt concentration. This indicates that the nature of interactions between proteins and solvent components is the same in solution and in the solid state, which implies no change in protein structure during precipitation. Analysis of the transfer free energies and preferential interaction parameter in terms of the salting-in, salting-out, and weak ion binding contributions has led to the conclusions that, when the weak ion binding contribution is small, the predominant protein-salt interaction must be that of preferential salt exclusion most probably caused by the increase of the surface tension of water by addition of the salt. A necessary consequence of this is salting-out of the protein, if the protein structure is to remain unaltered.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

T Arakawa, R Bhat, S N Timasheff. 1990-02-20. Preferential interactions determine protein solubility in three-component solutions: the MgCl2 system.. https://doi.org/10.1021/bi00459a036

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related citations

Molecular determinants for the recruitment of the ubiquitin-ligase MuRF-1 onto M-line titin.

Titin forms an intrasarcomeric filament system in vertebrate striated muscle, which has elastic and signaling properties and is thereby central to mechanotransduction. Near its C-terminus and directly preceding a kinase domain, titin contains a conserved pattern of Ig and FnIII modules (Ig(A168)-Ig(A169)-FnIII(A170), hereby A168-A170) that recruits the E3 ubiquitin-ligase MuRF-1 to the filament. This interaction is thought to regulate myofibril turnover and the trophic state of muscle. We have elucidated the crystal structure of A168-A170, characterized MuRF-1 variants by circular dichroism (CD) and SEC-MALS, and studied the interaction of both components by isothermal calorimetry, SPOTS blots, and pull-down assays. This has led to the identification of the molecular determinants of the binding. A168-A170 shows an extended, rigid architecture, which is characterized by a shallow surface groove that spans its full length and a distinct loop protrusion in its middle point. In MuRF-1, a C-terminal helical domain is sufficient to bind A168-A170 with high affinity. This helical region predictably docks into the surface groove of A168-A170. Furthermore, pull-down assays demonstrate that the loop protrusion in A168-A170 is a key mediator of MuRF-1 recognition. Our findings indicate that this region of titin could serve as a target to attempt therapeutic inhibition of MuRF-1-mediated muscle turnover, where binding of small molecules to its distinctive structural features could block MuRF-1 access.

Calorimetry↗

How does dextran sulfate prevent heat induced aggregation of protein? The mechanism and its limitation as aggregation inhibitor.

The effect of dextran sulfate on protein aggregation was investigated to provide the clues of its biochemical mechanism. The interaction between dextran sulfate and BSA varied with the pH values of the solution, which led to the different extent of aggregation prevention by dextran sulfate. Light scattering data with thermal scan showed that dextran sulfate suppressed BSA aggregation at pH 5.1 and pH 6.2, while it had no effect at pH 7.5. Isothermal titration calorimetric analysis suggested that the pH dependency of the role of dextran sulfate on BSA aggregation would be related to the difference in the mode of BSA-dextran sulfate complex formation. Isothermal titration calorimetric analysis at pH 6.2 indicated that dextran sulfate did not bind to native BSA at this pH, but interacted with partially unfolded BSA. While stabilizing native form of protein by the complex formation has been suggested as the suitable mechanism of preventing aggregation, our observation of conformational changes by circular dichroism spectroscopy showed that strong electrostatic interaction between dextran sulfate and BSA rather facilitated the denaturation of BSA. Combining the data from isothermal titration calorimetry, circular dichroism, and dynamic light scattering, we found that the complex formation of the intermediate state of denatured BSA with dextran sulfate is a prerequisite to suppress the aggregation by preventing further oligomerization/aggregation process of denatured protein.

Calorimetry↗

Formulation, lyophilization and solid-state properties of a pegylated protein.

In this paper the importance of formulation and process parameters on the solid-state properties of a lyophilized, pegylated growth hormone antagonist (pegvisomant) was studied. The degree of solid-state disorder (amorphicity), protein/polyethylene glycol (PEG)/sucrose interactions, and dissolution characteristics of the resultant cakes were examined. Using isothermal microcalorimetry (IMC) and differential scanning calorimetry (DSC), it was shown that in co-lyophilized pegylated protein/sucrose systems there was an interaction between sucrose and pegylated protein molecules. This interaction was evidenced by a decrease in the melting temperature (Tm) and melting enthalpy of PEG as a function of sucrose concentration. It was also shown that the sum of the heat of interaction with water for the individual constituents, lyophilized pegylated protein and lyophilized sucrose, was higher than the heat of interaction for the co-lyophilized system. As the concentration of sucrose was increased, the degree of solid-state disorder increased and the solid dissolved faster. A correlation was found among heat of interaction with water, degree of solid-state disorder, and dissolution time. Pegylation caused a shorter dissolution time, lower moisture content, increased amorphicity, and a more rapid moisture-induced crystallization of sucrose.

Calorimetry↗