PubMed Health⌕ Search

PubMed · 464780

Electromyographic insertional activity in normal limb muscles.

Abstract

A mechanical electrode inserter was used to allow reproducible electromyographic (emg) electrode insertions. The electrical activity provoked by the mechanical insertion was recorded and quantitatively analyzed in the anterior tibialis, the extensor hallucis longus, and the extensor digitorum brevis of unimpaired human subjects. No statistically significant differences were found among these muscles in the total duration of sharp spike activity or in the duration of sharp spike activity following cessation of needle electrode movement. There was a statistically significant reduction in the total duration of mechanically-provoked electrical activity in the extensor digitorum brevis when compared to the anterior tibialis using the technique employed in this study. There was a statistically significant increase in time following the onset of needle electrode movement until the initiation of sharp spike activity in the extensor hallucis longus as compared to the anterior tibialis. Abnormalities are present in the extensor digitorum brevis muscle of clinically unimpaired subjects. Endplate spikes can be recorded as positive-shaped potentials in the endplate zones of muscle. Nonreproducible positive-shaped potentials of unknown etiology are seen to occur singly or in pairs following insertional activity in normal muscle. When examining muscle for the early evidence of provokable positive sharp wave and fibrillation potentials, care must be taken not to mistake normal characteristics of insertional activity for pathological abnormalities.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

D O Wiechers. 1979. Electromyographic insertional activity in normal limb muscles.. https://pubmed.ncbi.nlm.nih.gov/464780/

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related citations

Probing spin accumulation in Ni/Au/Ni single-electron transistors with efficient spin injection and detection electrodes.

We have investigated spin accumulation in Ni/Au/Ni single-electron transistors assembled by atomic force microscopy. The fabrication technique is unique in that unconventional hybrid devices can be realized with unprecedented control, including real-time tunable tunnel resistances. A grid of Au disks, 30 nm in diameter and 30 nm thick, is prepared on a SiO2 surface by conventional e-beam writing. Subsequently, 30 nm thick ferromagnetic Ni source, drain, and side-gate electrodes are formed in similar process steps. The width and length of the source and drain electrodes were different to exhibit different coercive switching fields. Tunnel barriers of NiO are realized by sequential Ar and O2 plasma treatment. By use of an atomic force microscope with specially designed software, a single nonmagnetic Au nanodisk is positioned into the 25 nm gap between the source and drain electrodes. The resistance of the device is monitored in real time while the Au disk is manipulated step-by-step with angstrom-level precision. Transport measurements in magnetic field at 1.7 K reveal no clear spin accumulation in the device, which can be attributed to fast spin relaxation in the Au disk. From numerical simulations using the rate-equation approach of orthodox Coulomb blockade theory, we can put an upper bound of a few nanoseconds on the spin-relaxation time for electrons in the Au disk. To confirm the magnetic switching characteristics and spin injection efficiency of the Ni electrodes, we fabricated a test structure consisting of a Ni/NiO/Ni magnetic tunnel junction with asymmetric dimensions of the electrodes similar to those of the single-electron transistors. Magnetoresistance measurements on the test device exhibited clear signs of magnetic reversal and a maximum tunneling magnetoresistance of 10%, from which we deduced a spin polarization of about 22% in the Ni electrodes.

Electrodes↗

Organized assemblies of single wall carbon nanotubes and porphyrin for photochemical solar cells: charge injection from excited porphyrin into single-walled carbon nanotubes.

Photochemical solar cells have been constructed from organized assemblies of single-walled carbon nanotubes (SWCNT) and protonated porphyrin on nanostructured SnO2 electrodes. The protonated form of porphyrin (H4P2+) and SWCNT composites form 0.5-3.0 microm-sized rodlike structures and they can be assembled onto nanostructured SnO2 films [optically transparent electrode OTE/SnO2] by an electrophoretic deposition method. These organized assemblies are photoactive and absorb strongly in the entire visible region. The incident photon to photocurrent efficiency (IPCE) of OTE/SnO2/SWCNT-H4P2+ is approximately 13% at an applied potential of 0.2 V versus saturated calomel electrode. Femtosecond pump-probe spectroscopy experiments confirm the decay of the excited porphyrin in the SWCNT-H4P2+ assembly as it injects electrons into SWCNT. The dual role of SWCNT in promoting photoinduced charge separation and facilitating charge transport is presented.

Electrodes↗

Free flow isotachophoresis in an injection moulded miniaturised separation chamber with integrated electrodes.

An injection moulded free flow isotachophoresis (FFITP) microdevice with integrated carbon fibre loaded electrodes with a separation chamber of 36.4mm wide, 28.7 mm long and 100 microm deep is presented. The microdevice was completely fabricated by injection moulding in carbon fibre loaded polystyrene for the electrodes and crystal polystyrene for the remainder of the chip and was bonded together using ultrasonic welding. Two injection moulded electrode designs were compared, one with the electrode surface level with the separation chamber and one with a recessed electrode. Separations of two anionic dyes, 0.2mM each of amaranth and acid green and separations of 0.2mM each of amaranth, bromophenol blue and glutamate were performed on the microdevice. Flow rates of 1.25 ml min(-1) for the leading and terminating electrolytes were used and a flow rate of 0.63 ml min(-1) for the sample. Electric fields of up to 370 V cm(-1) were applied across the separation chamber. Joule heating was not found to be significant although out-gassing was observed at drive currents greater than 3 mA.

Electrodes↗