PubMed · 6998750
The source did not provide an abstract. Follow the original record for more information.
Explore connections, maps & timelines
J Dénes, G Domokos, Z Elischer. 1980. [The direct bonding technic].. https://pubmed.ncbi.nlm.nih.gov/6998750/
Cite the original work for its findings. Save a collection to share your selection of sources.
KEEP EXPLORING
Despite the popularity of metal-ceramic restorations, the bonding mechanism remains the subject of theoretical discussion. Different experimental designs to evaluate bond strengths at the metal-ceramic interface are described. The effects of various stresses with each design are also discussed. A predictive experimental design should minimize variables and result in the least residual interfacial stresses. Dentists and dental technicians should benefit from comparisons of existing tests, and the discussion encourages introduction of more comprehensive approaches.
Preservation of the morphological integrity of demineralized dentin collagen in its hydrated state may account for the success observed in wet-bonding procedures. This study investigated the micromorphological differences between moist- and dry-bonding techniques with the use of: (a) Aelitebond, an alcohol-based, water-free, single-component dentin adhesive primer system; and (b) a water-free, acetone-based experimental primer similar to the acetone-based, water-containing All-Bond 2, a two-component primer system. In the wet groups, acid-conditioned dentin surfaces were blotted so that they remained visibly moist prior to bonding. In the dry groups, dentin surfaces were air-dried for 30 sec. Following the bonding procedures, dentin discs in each group were laminated together by means of a chemical-cure resin and processed for scanning electron microscope (SEM) and transmission electron microscope (TEM) examination. Conditioning with 10% H3PO4 for 20 sec. produced complete demineralization of the outer dentin. In the wet groups, banded collagen and interfibrillar spaces could be observed at the surface of the acid-conditioned dentin. Complete wetting of the loosely arranged collagen fibrils by the resin resulted in the formation of a hybrid layer. In the dry groups, only a very thin hybrid layer was observed on the dentin surface, along the walls of the tubules, and along the course of their lateral branches. The absence of banded collagen and interfibrillar spaces within these areas suggested the existence of a collapsed dentin matrix along various liquid-vapor boundaries that restricted resin permeation into the subsurface intertubular matrix, producing an incompletely infiltrated "hybridoid region".
The use of base metal alloys for porcelain fused to a metal crown and bridges has increased recently because of lower price, high hardness, high tensile strength and high elastic modulus. The addition of beryllium to base metal alloys increased fluidity and improved casting fitness. Beryllium also controlled surface oxidation and bonding strength. The bonding agent and gold bonding agent also affected the bonding strength between porcelain and metal alloys. Four commercially available ceramic base alloys were studied (two alloys contained beryllium element, another two did not). The purpose of this investigation was to study the microstructure between porcelain matrix, bonding agent and alloy matrix interfaces. A scanning electron micro-probe analyzer and energy dispersive X-ray spectroscopy (EDXS) were used to study the distribution of elements (Ni, Cr, Mo, Cu, O, Si, Sn, Al) in four base alloys. The following results were obtained: 1. The thickness of the oxidized layer of Rexillium III alloy and Unitbond alloy (contained beryllium) was thinner than Unibond alloy and Wiron 88 alloy (no beryllium). 2. The thickness of the oxidized layer of alloys in air (10 minutes and 30 minutes) was thinner in Unitbond (2.45 microns and 3.80 microns) and thicker in Wiron 88 (4.39 microns and 5.96 microns). 3. The thickness of the oxidized layer occurring for a duration of ten minutes (in vaccum) showed that the Rexillium III alloy was the thinnest (1.93 microns), and Wiron 88 alloy was the thickest (2.30 microns). But in thirty minutes (vacuum), Unitbond alloy was the thinnest (3.37 microns), and Wiron 88 alloy was the thickest (5.51 microns). 4. The intensity of Cr elements was increased obviously near the interface between Unitbond alloy, Wiron 88 alloy (no beryllium) and oxidized layer, but the intensity of Ni and Mo elements was slightly increased. The intensity of Cr element was not increased markedly between Rexillium III alloy, Unitbond alloy (beryllium) and oxidized layer. 5. A white-grayish oxidized layer appeared at the metal-ceramic interfaces but the thickness of oxidized layer was not obviously different. 6. The use of bonding agent at metal-ceramic interface leads to the deposition of many Sn elements at about 40 microns range within the porcelain surface. 7. Second interaction phases at the porcelain layer appeared when gold bonding agent was used, and a 50-100 microns microleakage occurred at the metal-ceramic interface.