PubMed Health⌕ Search
Home/Archive/PubMed

PubMed · 15484765

Developing methods to evaluate odour control products.

S Bouzalakos·B Jefferson·P J Longhurst·R M Stuetz
View original source ↗Export metadata ↓

Abstract

An economical and practical alternative to the standard end-of-pipe odour control methods is the application of liquid odour control products. Currently, there are no established product-testing methods. The data that are available are often of questionable quality and may have limited relevance to waste management. Waste facilities receive differing streams of waste at varying loading volumes. Whilst in operation this exposes control products to a wide variety of environmental conditions, further increasing the difficulty of selecting an effective means of control. The current study initially identifies commercially available odour control products applicable for solid and liquid waste management operations. Bench-scale batch absorption tests have been carried out to investigate odorous gas abatement for a range of selected commercial products and water at a range of pH values. Hydrogen sulphide was the test odorous gas, as it is commonly associated with waste processes. Gas-phase volumetric mass-transfer coefficients (KGa) have been calculated to determine mass-transfer performance. The development of a pilot-scale spray tower is then presented as the testing apparatus for future work. This is an attempt to construct a repeatable testing method for evaluating abatement performance of odour control products, and control the problems encountered when applying odour control products to open sites. KGa values and data collected from tests in this study will be considered in future work as design parameters for the rig.

Explore related subjects

AbsorptionAir PollutantsHydrogen SulfideOdorantsQuality ControlWaste Disposal, FluidJournal Article

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

S Bouzalakos, B Jefferson, P J Longhurst, R M Stuetz. 2004. Developing methods to evaluate odour control products.. https://pubmed.ncbi.nlm.nih.gov/15484765/

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related citations

PubMed2007

The use of an oil absorber as a strategy to overcome starvation periods in degrading 1,2-dichloroethane in waste gas.

This work investigates the use of an oil absorber as an operational strategy in vapor phase bioreactors exposed to starvation periods, during the treatment of inhibitory pollutants. After being exposed to 1,2-dichloroethane (DCE) starvation periods, the response and stability of a combined oil-absorber-bioscrubber (OAB) system was compared to that of a bioscrubber only (BO) system. In the BO system, after a 5.2 days starvation period, the DCE removal efficiency was reduced to 12%, and 6 days were needed to recover the initial removal efficiency when the DCE feed resumed. The total organic discharged (TOD(DCE)) was 16,500 g(DCE) m(bioscrubber) (-3) after the DCE starvation. Biomass analysis performed using fluorescence in situ hybridisation (FISH) showed that the microbial activity was significantly reduced during the starvation period and that 5 days were needed to recover the initial activity, after the re-introduction of DCE. In contrast, the performance of the OAB system was stable during 5.2 days of DCE starvation. The DCE removal efficiency was not affected when the DCE feed resumed and the TOD(DCE) was significantly reduced to 2,850 g(DCE) m(bioscrubber) (-3). During starvation, the activity of the microbial culture in the OAB system showed a substantially lower decrease than in the BO system and recovered almost immediately the initial activity after the re-introduction of DCE. Additionally, a mathematical model describing the performance of the OAB system was developed. The results of this study show that the OAB system can effectively sustain the biological treatment of waste gas during starvation periods of inhibitory pollutants.

Absorption↗
PubMed2007

Sorption kinetics of ethanol/water solution by dimethacrylate-based dental resins and resin composites.

In the present investigation the sorption-desorption kinetics of 75 vol % ethanol/water solution by dimethacrylate-based dental resins and resin composites was studied in detail. The resins examined were made by light-curing of bisphenol A glycol dimethacrylate (Bis-GMA), triethylene glycol dimethacrylate (TEGDMA), urethane dimethacrylate (UDMA), bisphenol A ethoxylated dimethacrylate (Bis-EMA), and mixtures of these monomers. The resin composites were prepared from two commercial light-cured restorative materials (Z100 MP and Filtek Z250), the resin matrix of which is based on copolymers of the above-mentioned monomers. Ethanol/water sorption/desorption was examined in both equilibrium and dynamic conditions in two adjacent sorption-desorption cycles. For all the materials studied, it was found that the amount of ethanol/water sorbed or desorbed was always larger than the corresponding one reported in literature in case of water immersion. It was also observed that the chemical structure of the monomers used for the preparation of the resins directly affects the amount of solvent sorbed or desorbed, as well as sorption kinetics, while desorption rate was nearly unaffected. In the case of composites studied, it seems that the sorption/desorption process is not influenced much by the presence of filler. Furthermore, diffusion coefficients calculated for the resins were larger than those of the composites and were always higher during desorption than during sorption. Finally, an interesting finding concerning the rate of ethanol/water sorption was that all resins and composites followed Fickian diffusion kinetics during almost the whole sorption curve; however, during desorption the experimental data were overestimated by the theoretical model. Instead, it was found that a dual diffusion-relaxation model was able to accurately predict experimental data during the whole desorption curve. Kinetic relaxation parameters, together with diffusion coefficients, are reported for all resins and composites.

Absorption↗
PubMed2006

Production of red mold rice using a modified Nagata type koji maker.

In this research, a commercial koji maker with a rotary perforated bed of 5-m diameter was modified for red mold rice production. Monascus purpureus BCRC 31499 was selected for its high production capacities of monacolin K and red pigment. The selected strain was first cultivated in a 120-l submerged type fermentor at 34 degrees C and 2 vvm aeration rate with 60 rpm agitation for 5 days using 20% liquefied rice porridge as carbon source. The high concentration red mold rice broth (>3.5 g/ml) was harvested for inocula and well mixed with cooked rice to an initial concentration of 2% v/w. The inoculated cooked rice then was directed into the modified koji maker, in which temperature and humidity profiles were kept at varied levels at different stages, respectively. Air was circulated to remove fermentation heat while the perforated bed rotated slowly for providing mild agitation. Lag phase of the Monascus sp. in the modified koji maker was determined to be 16 h by the time the koji temperature raised rapidly. Water was added into the koji bed by a water curtain at the 36th hour to keep the moisture content of the rice koji at 50% or above. At the final stage, temperature was adjusted to 34 degrees C to direct red pigment production. After 7 days, 1,200-kg high quality red mold rice was harvested per batch. Labor costs, space, and fermentation time were reduced tremendously compared with those made by traditional methods.

Absorption↗