PubMed Health⌕ Search

PubMed · 8734595

Friction, not texture, dictates grip forces used during object manipulation.

Abstract

1. Three men and seven women, 25-40 yr of age, were asked to use the thumb and index fingers to grasp, lift, and hold the armature of a linear motor generating a 2.0-N opposing force (simulating an object weighing approximately 200 g) for 2 s. The surface in contact with the fingers was composed of smooth or polyamide plastic etched with 1.0-mm high Braille beads separated at 2.0- or 3.0-mm intervals measured from apex to apex. The surfaces were left either untreated or coated with talc, water, or sucrose films designed to change the coefficient of friction with the skin. Talc reduced the coefficient of friction, whereas water and sucrose both increased the friction against the skin. In all, 12 surface conditions were used to evaluate the effects of texture and friction on the grip force during lifting and holding. 2. For all subjects the inverse coefficient of friction was associated with proportionately scaled increases in grip force, regardless of surface texture. The peak lifting force as well as the static force used to hold the object stationary were significantly correlated with the inverse of the coefficient of friction. When coatings were applied to dissimilar surface textures to produce similar coefficients of friction, the grip force profiles were nearly identical. When strong adhesives increased the friction of the smooth surface compared with textured surfaces, grip forces decreased as friction increased. That is, although the untreated smooth surface had less friction than either of the two textured surfaces, the addition of sucrose increased the smooth surface friction to a higher level than either of the similarly treated textured surfaces. As a result, the effect of surface friction could be dissociated from the effect of either surface texture or coating. Friction appears to be a more important factor in determining the grip force than either texture or surface films at least for the range of textures and coatings examined in this study.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

G Cadoret, A M Smith. 1996. Friction, not texture, dictates grip forces used during object manipulation.. https://doi.org/10.1152/jn.1996.75.5.1963

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related citations

Effect of capillary condensation on friction force and adhesion.

Friction force measurements have been conducted with a colloid probe on mica and silica (both hydrophilic and hydrophobized) after long (24 h) exposure to high-humidity air. Adhesion and friction measurements have also been performed on cellulose substrates. The long exposure to high humidity led to a large hysteresis between loading and unloading in the friction measurements with separation occurring at large negative applied loads. The large hysteresis in the friction-load relationship is attributed to a contact area hysteresis of the capillary condensate which built up during loading and did not evaporate during the unloading regime. The magnitude of the friction force varied dramatically between substrates and was lowest on the mica substrate and highest on the hydrophilic silica substrate, with the hydrophobized silica and cellulose being intermediate. The adhesion due to capillary forces on cellulose was small compared to that on the other substrates, due to the greater roughness of these surfaces.

Adhesiveness↗

Evaluation of bond strength of soft relining materials to denture base polymers.

OBJECTIVES: To evaluate the initial bonding properties of recently and previously introduced soft relining materials to denture base polymers with different polymerization techniques and different water content. METHODS: The initial tensile bond strength of 10 soft liners (Mollosil Plus, Dentusil, Ufi gel Soft, GC Reline Soft, Silagum Comfort, Vertex Soft, Astron Soft, Molloplast B, Flexacryl Soft, Triad Resiline) to three denture base polymers (Paladon 65, Palapress Vario, Ivocap Plus) were assessed with a modified method. Paladon 65 specimens immersed in water for 3 months were also used to test the effect of water content of denture base polymer on bond strength results. After testing, a visual examination of the fracture surfaces and a SEM investigation of the interface structure were performed. Tensile strength of each soft liner material was also tested. Data were analyzed statistically by two-way ANOVA (alpha = 0.05). RESULTS: Significant differences were found among tensile bond strength results (P < 0.05). Vinyl poly(organosiloxane) soft liners (Mollosil Plus, Dentusil, Ufi gel Soft, GC Reline Soft, Silagum Comfort) and a plasticized PMMA soft liner (Vertex Soft) gave statistically similar bond strength results for different denture base polymers (P>0.05). For the other materials used (Astron Soft, Molloplast B, Flexacryl Soft, Triad Resiline), different denture base polymers caused significantly different results (P < 0.05). Poly(organosiloxane) based materials gave slightly higher bond strength results with water immersed specimens than with the dry specimens. SIGNIFICANCE: A wide variety of newly formulated soft liners used in this study gave comparable or better bond strength results compared to Molloplast B.

Adhesiveness↗

Flat and sigmoidally curved contact zones in vesicle-vesicle adhesion.

Using the membrane-bending elasticity theory and a simple effective model of adhesion, we study the morphology of lipid vesicle doublets. In the weak adhesion regime, we find flat-contact axisymmetric doublets, whereas at large adhesion strengths, the vesicle aggregates are nonaxisymmetric and characterized by a sigmoidally curved, S-shaped contact zone with a single invagination and a complementary evagination on each vesicle. The sigmoid-contact doublets agree very well with the experimentally observed shapes of erythrocyte aggregates. Our results show that in identical vesicles with large to moderate surface-to-volume ratio, the sigmoid-contact shape is the only bound morphology. We also discuss the role of sigmoid contacts in the formation of multicellular aggregates such as erythrocyte rouleaux.

Adhesiveness↗